Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Kohler K341 Question w/Pics


 
Post new topic    
View previous topic :: View next topic  
Author Message
dig123
New User


Joined: 17 Jan 2021
Posts: 4


Report to Moderator

PostPosted: Sun Jan 17, 2021 10:42 am    Post subject: Kohler K341 Question w/Pics Reply to specific post Reply with quote

Can I add washers to finish drawing this bearing plate down? I believe the 1 1/4" bolts I thought were spec are too long and are bottoming out. TIA
 
Back to top
View user's profile
dig123
New User


Joined: 17 Jan 2021
Posts: 4


Report to Moderator

PostPosted: Sun Jan 17, 2021 10:44 am    Post subject: Re: Kohler K341 Question w/Pics Reply to specific post Reply with quote


Sorry, the site won't let me upload photos. Just keeps saying my post contains one or more words that are restricted. Even though I didn't type anything. Just attached pictures.
 
Back to top
View user's profile
wore out
Tractor Expert


Joined: 01 Oct 2019
Posts: 2317


Report to Moderator

PostPosted: Sun Jan 17, 2021 11:01 am    Post subject: Re: Kohler K341 Question w/Pics Reply to specific post Reply with quote

If I am understanding what you are asking correctly, the proper bolts are 3/8" X 1".

Why not just get the correct bolts, should cost lest than a buck?

On the other hand, adding a couple of washers would work IF that doesn't raise the heads enough to get them in trouble with the stator or possibly, the flywheel magnets.
 
Back to top
View user's profile
dig123
New User


Joined: 17 Jan 2021
Posts: 4


Report to Moderator

PostPosted: Sun Jan 17, 2021 11:06 am    Post subject: Re: Kohler K341 Question w/Pics Reply to specific post Reply with quote

CVPost-wore out wrote:
(quoted from post at 12:01:30 01/17/21) If I am understanding what you are asking correctly, the proper bolts are 3/8" X 1".

Why not just get the correct bolts, should cost lest than a buck?

On the other hand, adding a couple of washers would work IF that doesn't raise the heads enough to get them in trouble with the stator or possibly, the flywheel magnets.


Yes, it will definitely clear. Sorry, should have been more clear. This will be temporary just to draw the plate down. Next time I'm in town I'll grab the correct bolts and swap them out. Where did you find the 1" spec? Thanks btw
 
Back to top
View user's profile
wore out
Tractor Expert


Joined: 01 Oct 2019
Posts: 2317


Report to Moderator

PostPosted: Sun Jan 17, 2021 11:19 am    Post subject: Re: Kohler K341 Question w/Pics Reply to specific post Reply with quote


"Where did you find the 1" spec?"

https://partscatalog.deere.com/jdrc/sidebyside/equipment/58755/referrer/navigation/pgId/143202

I believe the serial number break on the boots is that one style has captive lockwashers and the other doesn't, both are 1".
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 88574
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Sun Jan 17, 2021 11:55 am    Post subject: Re: Kohler K341 Question w/Pics Reply to specific post Reply with quote

If your new you have to ask permission to put picture up or have a number of post already
 
Back to top
View user's profile
dig123
New User


Joined: 17 Jan 2021
Posts: 4


Report to Moderator

PostPosted: Sun Jan 17, 2021 12:28 pm    Post subject: Re: Kohler K341 Question w/Pics Reply to specific post Reply with quote

Awesome, thank you!
 
Back to top
View user's profile
Brian G. NY
Tractor Expert


Joined: 02 Dec 2007
Posts: 1804
Location: Upstate New York

Report to Moderator

PostPosted: Sun Jan 17, 2021 6:59 pm    Post subject: Re: Kohler K341 Question w/Pics Reply to specific post Reply with quote

dig123 wrote:
(quoted from post at 19:42:30 01/17/21) Can I add washers to finish drawing this bearing plate down? I believe the 1 1/4" bolts I thought were spec are too long and are bottoming out. TIA


I have used a hacksaw or 4-1/2' cut off wheel in such cases.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Garden Tractors All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters