Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Reinforcing loader on D17


 
Post new topic    
View previous topic :: View next topic  
Author Message
jhncp
Regular


Joined: 22 May 2019
Posts: 384


Report to Moderator

PostPosted: Thu Jan 14, 2021 6:16 am    Post subject: Reinforcing loader on D17 Reply to specific post Reply with quote

I used my D17 to lift a disk I bought and it pick up the earth with it (6" frost). It also lefted up an entire John Deere 24T baler with kicker that had no wheels so I could back my trailer under it. The only issue I have is the support brackets on loader are giving out. I'm thinking I will need to make a bracket to go over the hood and then run some uprights to it from engine tractor frame bolts or?

 
Back to top
View user's profile
Jim.ME
Tractor Guru


Joined: 02 Mar 2018
Posts: 3703


Report to Moderator

PostPosted: Thu Jan 14, 2021 8:18 am    Post subject: Re: Reinforcing loader on D17 Reply to specific post Reply with quote


Reinforce them and see what bends next. Unless there is obvious deterioration of the supports it could be a sign of overloading. Just because it can lift something doesn't mean it should. JMHO
 
Back to top
View user's profile
Brian G. NY
Tractor Expert


Joined: 02 Dec 2007
Posts: 1665
Location: Upstate New York

Report to Moderator

PostPosted: Thu Jan 14, 2021 9:15 am    Post subject: Re: Reinforcing loader on D17 Reply to specific post Reply with quote

I wonder what model loader you have. Both the A-C model 400 and 500 loaders are set up like you propose to do. Looks easy to duplicate.

 
Back to top
View user's profile
jhncp
Regular


Joined: 22 May 2019
Posts: 384


Report to Moderator

PostPosted: Thu Jan 14, 2021 9:28 am    Post subject: Re: Reinforcing loader on D17 Reply to specific post Reply with quote

Allis Chalmers 170 made by freeman

 
Back to top
View user's profile
DrAllis
Tractor Expert


Joined: 18 Jan 2015
Posts: 1503


Report to Moderator

PostPosted: Thu Jan 14, 2021 3:46 pm    Post subject: Re: Reinforcing loader on D17 Reply to specific post Reply with quote

Over the top is fine, but there should also be one down near the bottom of the towers if there isn't one there already.
 
Back to top
View user's profile
jhncp
Regular


Joined: 22 May 2019
Posts: 384


Report to Moderator

PostPosted: Thu Jan 14, 2021 4:20 pm    Post subject: Re: Reinforcing loader on D17 Reply to specific post Reply with quote



 
Back to top
View user's profile
Alvin 41
Regular


Joined: 04 Oct 2018
Posts: 336


Report to Moderator

PostPosted: Thu Jan 14, 2021 5:47 pm    Post subject: Re: Reinforcing loader on D17 Reply to specific post Reply with quote

I had a Miller Quick -Attach Loader on a D-17 that had a frame around the tractor front that it rested on and was the ground foot when dismounted . It had 2 way lift cylinders and lifting a complete combine grain head onto a truck at full extension both cylinder rods bent. They were too small diameter for the piston .
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters