Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

diverter valve for CA?


 
Post new topic    
View previous topic :: View next topic  
Author Message
J&J
New User


Joined: 24 Apr 2021
Posts: 1


Report to Moderator

PostPosted: Sat Apr 24, 2021 8:25 am    Post subject: diverter valve for CA? Reply to specific post Reply with quote

I have a 52 CA with a model 8 trip loader and snap coupler blade. I'd like to mount Both to the tractor without the hydraulics interfering with one another. Is a diverter valve what I'm needing? If so, would I need to reroute the lift cylinders along with the loader cylinders directly to the diverter valve with one line from the pump to the valve? Any recommendations on a good reasonalbly price valve?

Any other suggestions on how to accomplish this?

Thanks
 
Back to top
View user's profile
DrAllis
Tractor Expert


Joined: 18 Jan 2015
Posts: 1584


Report to Moderator

PostPosted: Sat Apr 24, 2021 5:32 pm    Post subject: Re: diverter valve for CA? Reply to specific post Reply with quote

I think you're asking about a simple push/pull valve that has 3 ports. One port for the pump......one port for the blade.....one port for the loader. You set the valve for the blade and raise the blade off the ground and switch the valve to the loader and the blade stays raised up and the loader can then be used up and down and hold. To use the blade, you raise the loader up off the ground a couple feet and switch the valve and then use the blade while the loader is locked up off the ground. This system requires some oil level management on your part, as some oil is always missing from the sump when it is holding up one of the implements. Surplus Center in Nebraska item 9-6133 Prince selector valve 3/8" pipe threads 20 GPM $79.00
 
Back to top
View user's profile
4wdtom
Tractor Expert


Joined: 03 Oct 2014
Posts: 2177


Report to Moderator

PostPosted: Sun Apr 25, 2021 5:46 am    Post subject: Re: diverter valve for CA? Reply to specific post Reply with quote

You could Tee into the line with a valve to each implement, opening the one you wanted to function I would think.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters