Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

VAC driving me nuts


 
Post new topic    
View previous topic :: View next topic  
Author Message
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 89205
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Mon May 03, 2021 2:44 pm    Post subject: VAC driving me nuts Reply to specific post Reply with quote

So I have been trying to get a VAC running again. I've had it try to run many times but not run for more then a minute or so. Thought it was the carb so took carb off one that runs well. Still didn't run. Lost spark but has new points. Found wire had shorted out to the oil filter. Got that taken care of and got it to run just to find out the generator is locked up so belt started smoking. Oh well at least it did run and now on to things like making sure the radiator is good etc.
 
Back to top
View user's profile
John Saeli
Tractor Guru


Joined: 19 Dec 2009
Posts: 4317


Report to Moderator

PostPosted: Mon May 03, 2021 4:20 pm    Post subject: Re: VAC driving me nuts Reply to specific post Reply with quote

Well I'd say that's progress!!
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 89205
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Mon May 03, 2021 4:43 pm    Post subject: Re: VAC driving me nuts Reply to specific post Reply with quote

Yes a little bit of it. The one I have been trying tot get to run now has a carb off a known good runner and the good runner now has the carb off the non running one and yet both now run
 
Back to top
View user's profile
Tgrasher
Long Time User


Joined: 19 Dec 2019
Posts: 943


Report to Moderator

PostPosted: Mon May 03, 2021 6:47 pm    Post subject: Re: VAC driving me nuts Reply to specific post Reply with quote

Your doing better than me, used a 300 that I thought I had everything fixed to spread fertilizer. Worked great, washed the dust off when I got done and left it set to dry. Started it later to put it away and oil starts coming out the timing hole in the bell housing. Drove it to the shed and parked it.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters