Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Case engines


 
Post new topic    
View previous topic :: View next topic  
Author Message
LarryD Ont
New User


Joined: 03 May 2021
Posts: 2


Report to Moderator

PostPosted: Wed May 12, 2021 12:11 pm    Post subject: Case engines Reply to specific post Reply with quote

Hello fellas, I m looking for some help/information regarding a case G188 out of a 600 Case Combine has the same bolt pattern as a G164 out of a 510 B tractor...thanks Larry D....Ontario
 
Back to top
View user's profile
Denny K
Long Time User


Joined: 02 Jan 2008
Posts: 565


Report to Moderator

PostPosted: Wed May 12, 2021 2:29 pm    Post subject: Re: Case engines Reply to specific post Reply with quote

I asked the same question last week and was told no. The starter mount is different 2 bolt vs. 3 bolt and 188 is a little longer.
 
Back to top
View user's profile
Denny K
Long Time User


Joined: 02 Jan 2008
Posts: 565


Report to Moderator

PostPosted: Wed May 12, 2021 2:31 pm    Post subject: Re: Case engines Reply to specific post Reply with quote

On the Case forum on the 9th.
 
Back to top
View user's profile
LarryD Ont
New User


Joined: 03 May 2021
Posts: 2


Report to Moderator

PostPosted: Wed May 12, 2021 4:21 pm    Post subject: Re: Case engines Reply to specific post Reply with quote

I know the starter is different but is the bolt pattern the same on the front of the engine as well as the back...thanks for our time
 
Back to top
View user's profile
used red MN
Tractor Expert


Joined: 24 Aug 2013
Posts: 3315
Location: Coon Rapids, MN

Report to Moderator

PostPosted: Wed May 12, 2021 9:17 pm    Post subject: Re: Case engines Reply to specific post Reply with quote

Hello Larry welcome to YT. You should repost your question in the Case topic section, see link.
YT Case topic section

 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tool Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters