Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Snorkel lift


 
Post new topic    
View previous topic :: View next topic  
Author Message
Keith True
Long Time User


Joined: 18 Aug 2017
Posts: 569


Report to Moderator

PostPosted: Thu May 27, 2021 4:39 pm    Post subject: Snorkel lift Reply to specific post Reply with quote

I have an 06 TB 50 Snorkel list.The swing is either dead stop or full bore,top speed.I noticed the lift,on the same lever,is modulated,move it a little for slow,and move it more for faster.Same thing for the wheel drive.I just got to thinking that maybe it should be the same for the swing.I am pretty used to an antique JLG lift that hops around like a monkey,so I didn't think much of it.Is anybody here familiar with that machine,and if it has a pentiometer to send the juice down to the solonoids?I like to own shop manuals for everything I own,(or at least IT manuals),but so far I have only found used ones at $380.I'll find one eventually.
 
Back to top
View user's profile
Janicholson
Tractor Guru


Joined: 30 Jan 2004
Posts: 37139
Location: St. Cloud, MN

Report to Moderator

PostPosted: Thu May 27, 2021 7:19 pm    Post subject: Re: Snorkel lift Reply to specific post Reply with quote

Solenoid valves do not operate at various voltages. To reduce the speed, it must be restricted in flow with a variable flow control valve, or orifice. Jim
 
Back to top
View user's profile
markct
Tractor Expert


Joined: 05 Feb 2003
Posts: 2838


Report to Moderator

PostPosted: Fri May 28, 2021 2:45 am    Post subject: Re: Snorkel lift Reply to specific post Reply with quote

Not true, most use pulse width modulation to vary the speed on solenoid valves for manlifts, that being said not all functions are variable, our manlift has drive and boom variable but other functions are not. All depends on the design
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Crawlers, Dozers, Loaders and Backhoes All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters