Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Crank Shaft Pulley TO 35


 
Post new topic    
View previous topic :: View next topic  
Author Message
willor
Regular


Joined: 29 May 2009
Posts: 98


Report to Moderator

PostPosted: Mon May 31, 2021 1:46 pm    Post subject: Crank Shaft Pulley TO 35 Reply to specific post Reply with quote

Need to replace governor and cant get the crankshaft pulley to come
off crankshaft. Took out the center bolt and tried a pulley puller and
soaked in trans fluid and diesel, but not budging. Tried another puller
and still no success. Tried 3rd puller and put too much pressure on it
and the pulley broke at one of the pulley arms. See picture

I dont see any set screw, just the key on the spindle. Any ideas how
to get this off.



Serial Number List for Ferguson: Model TO 35

 
Back to top
View user's profile
Steve@Advance
Tractor Guru


Joined: 12 Nov 2013
Posts: 20473


Report to Moderator

PostPosted: Mon May 31, 2021 2:31 pm    Post subject: Re: Crank Shaft Pulley TO 35 Reply to specific post Reply with quote

It should be a slip fit.

Possibly someone used Locktite. Might try some heat.

I would put the bolt back in without the washer, push against the bolt so not to damage the threads.
 
Back to top
View user's profile
Bruce(OR)
Tractor Guru


Joined: 10 Apr 2007
Posts: 3743


Report to Moderator

PostPosted: Mon May 31, 2021 9:38 pm    Post subject: Re: Crank Shaft Pulley TO 35 Reply to specific post Reply with quote

Heat the pulley only. Keep heat away from crank.
 
Back to top
View user's profile
willor
Regular


Joined: 29 May 2009
Posts: 98


Report to Moderator

PostPosted: Fri Jun 04, 2021 10:12 am    Post subject: Re: Crank Shaft Pulley TO 35 Reply to specific post Reply with quote

Fianlly came off with the heat, but it hung on until I had it almost all the way off the shaft. Not sure what was keeping is stuck no rust or other things on the shaft
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters