Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Re: sway bars


 
Post new topic    
View previous topic :: View next topic  
Author Message
T.R.K.
Tractor Expert


Joined: 14 Apr 2013
Posts: 2627


Report to Moderator

PostPosted: Fri Jun 04, 2021 5:33 pm    Post subject: Re: sway bars Reply to specific post Reply with quote

There is a list of parts suppliers on www.jetstar.minneapolismoline.com.
I have personally dealt with Wendell Everett and Welter's Farm Supply and been happy with their service every time. (Wendell is only part
time-he farms too-so keep calling until you get him.)

I don't have a picture to send you but basically, MM set up their sway bars so they go to the center between the pto and the drawbar. There
was a separate piece mounted in a yoke above the drawbar with a hole about 3 from the end that pivoted in the yoke and this allowed for
minor problems with the difference in the sway bar and the lift arm pivot points. The sway bars themselves were pinned in that hole in that
yoke.
 
Back to top
View user's profile
sodly
Long Time User


Joined: 29 Jun 2006
Posts: 645


Report to Moderator

PostPosted: Tue Jun 08, 2021 12:57 pm    Post subject: Re: sway bars Reply to specific post Reply with quote

Thanks TRK. Do you still have bars on your Jet Star? Have tried all the usual sources for these with no luck. I'm wondering if anyone out there ever used the factory sway bars.... or if anyone still uses them. More photos-- and especially DIMENSIONS-- would be most helpful as I may end up having to make my own. Could you provide any photos of yours? I know there were different length bars for category 1 vs category 2. I'm looking for cat 2. Could you measure your bars, hole center-to-hole center? That's going to be the critical dimension. Thanks!

This post was edited by sodly on 06/08/2021 at 02:11 pm.

 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters