Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

NH BR7070


 
Post new topic    
View previous topic :: View next topic  
Author Message
Fordfarmer
Tractor Guru


Joined: 12 Dec 2005
Posts: 10419
Location: Ladysmith, WI

Report to Moderator

PostPosted: Mon Jun 14, 2021 12:57 pm    Post subject: NH BR7070 Reply to specific post Reply with quote

Might not be a Ford, but it will be pulled by one. Baribeau Implement just delivered this today. Always hired my round baling done, until now.


Probably have to keep the crop cutter disengaged, since the minimum recommended h.p. with it is something like 105. 7600 will be working!
 
Back to top
View user's profile
mtf
Long Time User


Joined: 25 Aug 2013
Posts: 651


Report to Moderator

PostPosted: Wed Jun 16, 2021 5:34 pm    Post subject: Re: NH BR7070 Reply to specific post Reply with quote

Those 7000 series balers are outstanding. That wide pickup is something you will really like.
 
Back to top
View user's profile
chevytaHOE5674
Tractor Expert


Joined: 19 Mar 2009
Posts: 1970
Location: Western UP, Mi

Report to Moderator

PostPosted: Thu Jun 17, 2021 8:58 pm    Post subject: Re: NH BR7070 Reply to specific post Reply with quote

Pull the same baler with an 8830 or T7050 and with the knives engaged in heavy wet crop it'll make 180hp work at 9mph.
 
Back to top
View user's profile
chevytaHOE5674
Tractor Expert


Joined: 19 Mar 2009
Posts: 1970
Location: Western UP, Mi

Report to Moderator

PostPosted: Thu Jun 17, 2021 9:00 pm    Post subject: Re: NH BR7070 Reply to specific post Reply with quote

Should mention i ran it on 105hp when I was down a tractor and even with the knives retracted it made that old girl work. Couldn't run the A/C in the cab or it would overheat.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters