Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

V Grooved pulley in Place of Flat Pulley.


 
Post new topic    
View previous topic :: View next topic  
Author Message
MarB
Regular


Joined: 20 Oct 2007
Posts: 59


Report to Moderator

PostPosted: Sun Jun 13, 2021 10:58 am    Post subject: V Grooved pulley in Place of Flat Pulley. Reply to specific post Reply with quote


Hi there . Can anyone tell me if and where the V Groove pulley shown in the photo is available.. Tractor in photo is a Fordson Major. Thanks for looking.



This post was edited by MarB on 06/13/2021 at 12:29 pm.

 
Back to top
View user's profile
560Dennis
Long Time User


Joined: 10 Dec 2015
Posts: 1102


Report to Moderator

PostPosted: Wed Jun 30, 2021 3:01 am    Post subject: Re: V Grooved pulley in Place of Flat Pulley. Reply to specific post Reply with quote

Bearing Distributors inc.
made by mfg. s (Browning) ,(Martin),(Boston) others
 
Back to top
View user's profile
MarB
Regular


Joined: 20 Oct 2007
Posts: 59


Report to Moderator

PostPosted: Thu Jul 01, 2021 6:37 am    Post subject: Re: V Grooved pulley in Place of Flat Pulley. Reply to specific post Reply with quote

CVPost-560Dennis wrote:
(quoted from post at 12:01:36 06/30/21) Bearing Distributors inc.
made by mfg. s (Browning) ,(Martin),(Boston) others

Thanks for the reply. I checked the manufacturers listed . From what I can gather drive pulleys are available with same type & dimension center hub ,using the wedge sleeve design , however none appear to be machined with the inner seal mating surface which is integral with factory pulley . As well , this seal wiping gland boss cast into the pulley controls end play with outer bearing race contact.

This post was edited by MarB on 07/01/2021 at 07:38 am.

 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Fordson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters