Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Ertl tractor tire sizes


 
Post new topic    
View previous topic :: View next topic  
Author Message
Brockpend
Regular


Joined: 11 Jan 2021
Posts: 20


Report to Moderator

PostPosted: Wed Aug 04, 2021 3:37 pm    Post subject: Ertl tractor tire sizes Reply to specific post Reply with quote

This is probably a dumb question but Im new to diecast ertls so bear with me, but how do you measure tire size?
 
Back to top
View user's profile
tractorguy2
Tractor Guru


Joined: 24 May 2014
Posts: 4274


Report to Moderator

PostPosted: Wed Aug 04, 2021 5:52 pm    Post subject: Re: Ertl tractor tire sizes Reply to specific post Reply with quote

The older toys the tires have no sizes marked. They are measured by their physical size. Most common is one inch by four inch rear tire. Newer toys the tires will have a size on the side walls like 18.4x38.

If you want some nice buy slightly pricey custom tires. Check out chuckysprecisionpullersandparts.com
 
Back to top
View user's profile
Buckeye Oliver collector
Tractor Expert


Joined: 09 Feb 2007
Posts: 1621


Report to Moderator

PostPosted: Sun Aug 22, 2021 8:02 pm    Post subject: Re: Ertl tractor tire sizes Reply to specific post Reply with quote

The most common sized Ertl rear tires are called 1 inch by 4 inch and 1 1/2 inch by 4 inch, though they are closer to 1 and 3/4 by 4. There is a noticeable difference between the ones and one-one/half. The one by fours are on tractors like the IH 706. 806, 826, JD R, 80, Case 600, 800 etc. These will many times have single rib front tires, sometimes plastic. Something like the Allis Chalmers D21, 220, 7000 series, John Deere 5020s, Case 2590, 2594, 3294 will have the fatter rear tires. Likewise on the front tires the tires will be wider for the tractors with the 1- 1/2 by 4s. Cannot remember the numbers but they are called two-rib for the tread pattern. Again wider on the fronts of the big Allis, Case and John Deere toys. Also the same size used on the original Massey 1155 toys. As mentioned, there are radials and custom pulling tires now that are usually marked with the tire size on the sidewalls of the tire just like the full size ones. Hope this helps.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Memorabilia All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters