Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Hit Miss Valve Stem Clearance


 
Post new topic    
View previous topic :: View next topic  
Author Message
Steve@Advance
Tractor Guru


Joined: 12 Nov 2013
Posts: 21356


Report to Moderator

PostPosted: Wed Jun 09, 2021 11:12 am    Post subject: Hit Miss Valve Stem Clearance Reply to specific post Reply with quote

Trying to get my Fairbanks Morse 3HP ZC back together.

Took the valves out, the seats and faces look great.

The stems have minimal wear, they check at .373 to .371.

But the guides are really loose. Checking with gauge pins I get .387 on the intake, .382 on the exhaust.

I have no idea what they are supposed to be. Is this acceptable for it being an open valve train?

It's just going to be a running display motor unless I can come up with something for it to run, still it's working days are over. Just want it to start easy and idle down.

Thanks!
 
Back to top
View user's profile
warbaby
Tractor Expert


Joined: 21 Aug 2016
Posts: 1725


Report to Moderator

PostPosted: Wed Jun 09, 2021 5:04 pm    Post subject: Re: Hit Miss Valve Stem Clearance Reply to specific post Reply with quote

That intake valve has to be pretty loose so suction will open it and that weak spring will help snap it shut on compression. I dont really think there is a factory spec, just loose enough to easily push in without any excessive side-to-side play. The mechanically actuated exhaust valve can be a bit tighter in the guide, I suppose.
Bush them and then ream them to size- trial and error until you get a fit that feels right- and dont forget to drill out the oil weep holes!
 
Back to top
View user's profile
neverfear
Long Time User


Joined: 02 May 2010
Posts: 585


Report to Moderator

PostPosted: Wed Jun 09, 2021 5:07 pm    Post subject: Re: Hit Miss Valve Stem Clearance Reply to specific post Reply with quote

Well, there is probably a spec somewhere but what I go by is if the valve reliably comes down on the seat and seals it's good enough for these old engines. Usually it's the exhaust valve that will give you problems first since it has the most travel. The intake never really opens, it just flutters enough (hence the weaker spring) to let a charge of fuel/air in. With the springs off close the valve and rock the stem side to side. You'll be fine with up to an eighth inch deflection at the tip of the stem. More than that and I would expect inconsistent sealing of the valve. Give the stems a shot of oil and push the valves open and close every time before you start it. Good Luck!
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Stationary Engines All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters