Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Planishiing hammer anvils I made.


 
Post new topic    
View previous topic :: View next topic  
Author Message
dr sportster
Tractor Guru


Joined: 27 Jul 2011
Posts: 9958


Report to Moderator

PostPosted: Sat Oct 09, 2021 8:08 am    Post subject: Planishiing hammer anvils I made. Reply to specific post Reply with quote

Here are a few planishing hammer anvils I made to work aluminum panels . They are for sale on eBay. 1 1/2 brass stock and nylon upper anvil.
Shank for nylon is H-F chisel cut off on chop saw and pressed in .
 
Back to top
View user's profile
glennster
Tractor Guru


Joined: 14 Aug 2007
Posts: 13756
Location: illinois

Report to Moderator

PostPosted: Sat Oct 09, 2021 6:09 pm    Post subject: Re: Planishiing hammer anvils I made. Reply to specific post Reply with quote

they look great! nice work!
 
Back to top
View user's profile
MarkB_MI
Tractor Guru


Joined: 29 Aug 2004
Posts: 15881


Report to Moderator

PostPosted: Sun Oct 10, 2021 12:11 am    Post subject: Re: Planishiing hammer anvils I made. Reply to specific post Reply with quote

Very nice!
 
Back to top
View user's profile
DoubleO7
Tractor Guru


Joined: 27 Oct 2017
Posts: 6532


Report to Moderator

PostPosted: Sun Oct 10, 2021 7:29 am    Post subject: Re: Planishiing hammer anvils I made. Reply to specific post Reply with quote


Very nice!

So.......what is the end game for these aluminum panels??

Maybe a pre war Bugatti restoration???
 
Back to top
View user's profile
bentstick
Regular


Joined: 08 May 2020
Posts: 61


Report to Moderator

PostPosted: Thu Oct 14, 2021 4:58 pm    Post subject: Re: Planishiing hammer anvils I made. Reply to specific post Reply with quote

DoubleO7 wrote:
(quoted from post at 12:29:33 10/10/21)
Very nice!

So.......what is the end game for these aluminum panels??

Maybe a pre war Bugatti restoration???



Newer Ford trucks Laughing
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Tool Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters