Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Wallowed out starter hole pic


 
Post new topic    
View previous topic :: View next topic  
Author Message
Indiana Jones
Long Time User


Joined: 05 Sep 2001
Posts: 893


Report to Moderator

PostPosted: Sat Jul 07, 2007 5:58 am    Post subject: Wallowed out starter hole pic Reply to specific post Reply with quote

There's been discussion here before on many occasions about "wallowing out" the starter hole at 2 o'clock to make removal and replacement easier. Got the N apart, so I took a pic of what it looks like on mine.

 
Back to top
View user's profile
Bob
Tractor Guru


Joined: 03 Jan 1998
Posts: 55452


Report to Moderator

PostPosted: Sat Jul 07, 2007 6:00 am    Post subject: BAD clutch Reply to specific post Reply with quote

That clutch will NEVER work! It's TOO CLEAN!
 
Back to top
View user's profile
Indiana Jones
Long Time User


Joined: 05 Sep 2001
Posts: 893


Report to Moderator

PostPosted: Sat Jul 07, 2007 6:04 am    Post subject: Re: BAD clutch Reply to specific post Reply with quote

Nawww...I dripped some paint on it! I didn't want it to look too nice.
 
Back to top
View user's profile
Ray Wlson
Guest






Report to Moderator

PostPosted: Sat Jul 07, 2007 7:06 am    Post subject: Re: Wallowed out starter hole pic Reply to specific post Reply with quote

Indy,

Mine looked like that a month ago!

Photo Sharing and Video Hosting at Photobucket

Ray
 
Back to top
Tom N MS
Guest






Report to Moderator

PostPosted: Sat Jul 07, 2007 12:14 pm    Post subject: Re: Wallowed out starter hole pic Reply to specific post Reply with quote

They all need wallowed out. It is near impossible to get them out unless you just get lucky. tried to get mine out the other day while I had my tractor split(still split)and I never got it out till I dropped the flywheel. I'm installing the new style bendix and it looks like it should go in and out easier.
 
Back to top
Indiana Jones
Long Time User


Joined: 05 Sep 2001
Posts: 893


Report to Moderator

PostPosted: Sat Jul 07, 2007 4:03 pm    Post subject: Re: Wallowed out starter hole pic Reply to specific post Reply with quote

Tom-

New style bendix will go in much easier.

BTDT

Mark
 
Back to top
View user's profile
Tom N MS
Guest






Report to Moderator

PostPosted: Sat Jul 07, 2007 6:01 pm    Post subject: Re: Wallowed out starter hole pic Reply to specific post Reply with quote

Thanks. Good, there sure was room for improvement.
Have the new bendix on the starter. Went out a few minutes late today to mount the starter then wait for the flywheel to come from the machine shop. Wound up spending about 2 hours scraping off layers of grease and paint that are so much easier to reach while it is split..Part of the clutch job I did not really plan on...but you know how it goes...not a show tractor but like for it to look decent and be mechanically as good as possible.. http://www.tractorshed.com/cgi-bin/gallery/photo_pic.cgi?pic=http;//www.tractorshed.com/gallery/tphotos/a24697.jpg&firstrec=1&lastrec=15&Parameter=Prestridge&mode=All&what=tphotos
 
Back to top
:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). We have the parts you need to repair your tractor - the right parts. Our fast shipping, low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters