Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Oil leak at governor


 
Post new topic    
View previous topic :: View next topic  
Author Message
DoneDeere
New User


Joined: 01 Jun 2008
Posts: 16
Location: Upstate New York

Report to Moderator

PostPosted: Sun Jun 01, 2008 4:49 pm    Post subject: Oil leak at governor Reply to specific post Reply with quote

I just received a nice running 1952 Allis model B with oil leaking from the top of my govenor. The oil line enters the top of govenor through a steel bushing that acts like a bearing for the govenor arms and linkage to the carbuerator. This oil line with bushing slides up and down and is not fastened in place. Engine oil squarts out around the bushing. How do I secure the oil line and stop the oil leaking out? Thanks, DoneDeere.
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 86058
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Sun Jun 01, 2008 5:24 pm    Post subject: Re: Oil leak at governor Reply to specific post Reply with quote

That line should have a farrel on it to hold it in.
Hobby farm

 
Back to top
View user's profile
DoneDeere
New User


Joined: 01 Jun 2008
Posts: 16
Location: Upstate New York

Report to Moderator

PostPosted: Mon Jun 02, 2008 4:22 pm    Post subject: Re: Oil leak at governor Reply to specific post Reply with quote

Can you tell me more about this ferrel? My oil line attaches to a metal pin type part that is about 3/8" X 1" long. This part slides up and down into the govenor and lets the oil seep out around it. This pin acts like the pivot for the rods going to the carbueratur and throttle. Where does the ferrel attach and what does it look like? I do not have a parts catalog.
Thanks Larry
 
Back to top
View user's profile
Randy 1
Guest






Report to Moderator

PostPosted: Mon Jun 02, 2008 6:20 pm    Post subject: Re: Oil leak at governor Reply to specific post Reply with quote

Is the oil line moving up and down or is the bushing? The bushing you mention should be pressed in and is a hollow tube for oil to go from the line in to the govenor. The ferrel is a oval shaped brass fitting that slides over your 1/8 inch oil line. when the cap nut is tightened the ferrel puts pressure on the line to hold it in place.
 
Back to top
DoneDeere
New User


Joined: 01 Jun 2008
Posts: 16
Location: Upstate New York

Report to Moderator

PostPosted: Tue Jun 03, 2008 2:52 am    Post subject: Re: Oil leak at governor Reply to specific post Reply with quote

OK, I am missing the ferrel. My oil line is firmly attached to the barrel piece and the barrell with line attached moves up and down freely and out comes the oil. There is nothing holding the line/barrel to the govenor. Thank you.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters