Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Finish mower


 
Post new topic    
View previous topic :: View next topic  
Author Message
BAW
New User


Joined: 27 Jul 2008
Posts: 9


Report to Moderator

PostPosted: Wed Jun 03, 2009 4:32 am    Post subject: Finish mower Reply to specific post Reply with quote

Can anyone tell me if a 6ft finish mower is to big for my B. If so, how big can I go?

Thanks.
 
Back to top
View user's profile
chalmersbob
Guest






Report to Moderator

PostPosted: Wed Jun 03, 2009 6:01 pm    Post subject: Re: Finish mower Reply to specific post Reply with quote

it shouldn't be any problem at all. I run a 6'brush hog on my ca through some tough stuff. Bob
 
Back to top
Mike in Ohio
Regular


Joined: 02 Feb 2002
Posts: 429


Report to Moderator

PostPosted: Wed Jun 03, 2009 6:31 pm    Post subject: Re: Finish mower Reply to specific post Reply with quote

I run a 6' land pride behind mine runs it just fine, won't pick it up though. It comes up about a foot them the front end comes up and the mower settles back down on the ground. I put two of the weights that mount to the side of the engine on it, I think they are 90# apeice and three oliver front wheel weights mounted to a homemade bracket on the front axle. I don't know what those weighed. The front end stayed on the ground but still got pretty light. Plenty of power for it though. Good luck, Mike
 
Back to top
View user's profile
BAW
New User


Joined: 27 Jul 2008
Posts: 9


Report to Moderator

PostPosted: Thu Jun 04, 2009 3:47 am    Post subject: Re: Finish mower Reply to specific post Reply with quote

Thanks for the info guys. This site is great, everybody always takes the time to answer my silly questions.

Thanks again.
 
Back to top
View user's profile
dakota dave
Regular


Joined: 31 Jan 2005
Posts: 194


Report to Moderator

PostPosted: Sun Jun 07, 2009 6:37 am    Post subject: Re: Finish mower Reply to specific post Reply with quote

I have a l306 woods on my C. It works very well and cuts nice. the belly mowers hang the wieght low. in the middle of the tractor. With 700 lbs hanging in the center it is real stable.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters