Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Questions about Case 400


 
Post new topic    
View previous topic :: View next topic  
Author Message
Stephen F
New User


Joined: 07 Sep 2010
Posts: 1


Report to Moderator

PostPosted: Tue Sep 07, 2010 3:10 pm    Post subject: Questions about Case 400 Reply to specific post Reply with quote

Recently purchased another Case 400, which is gas. I have found out that the nose cone on this tractor is longer than my diesel 400 nose cones. Could this possibly mean that this is a super or is this the nature of the gas 400? Any help is greatly appreciated.
 
Back to top
View user's profile
INCase
Tractor Expert


Joined: 22 Jul 2002
Posts: 2248
Location: Indiana

Report to Moderator

PostPosted: Wed Sep 08, 2010 3:18 am    Post subject: Re: Questions about Case 400 Reply to specific post Reply with quote

presume you're talking about the large 400's.

The 400,700,800,730,830 westerns (and standards??) had different front bolsters which were shorter than the row-crop/general purpose models. That might be what you're seeing here.
 
Back to top
View user's profile
Stphen
Guest






Report to Moderator

PostPosted: Wed Sep 08, 2010 3:42 pm    Post subject: Re: Questions about Case 400 Reply to specific post Reply with quote

No all of the tractors im working with are row-crop. i dont under stand why three out of the four tractors we own have long nose. Only the one tractor has a short nose. By the way im building the gas in to a puller any one have any cheap horse power ideas.
 
Back to top
INCase
Tractor Expert


Joined: 22 Jul 2002
Posts: 2248
Location: Indiana

Report to Moderator

PostPosted: Thu Sep 09, 2010 6:07 am    Post subject: Re: Questions about Case 400 Reply to specific post Reply with quote

Can't remember if both the western's AND standards had the short front. The standards may not have.

A couple pictures of all of them would help us identify what you've got.

I've heard of guys modifying the block and putting in 830 or 870 pistons and sleeves and working the heads and putting bigger valves in. LP heads would give you more compression and a bit more HP too.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters