Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Installation of Head Gasket


 
Post new topic    
View previous topic :: View next topic  
Author Message
mike baker
New User


Joined: 03 Apr 2011
Posts: 4


Report to Moderator

PostPosted: Tue May 24, 2011 6:31 pm    Post subject: Installation of Head Gasket Reply to specific post Reply with quote

Where can I acquire the dowels and removal tongs for a 930 Case Head Gasket? I would also greatly appreciate any other information anyone can give me on these tools.
Thank you.
 
Back to top
View user's profile
Case Nutty 1660
Tractor Guru


Joined: 08 Mar 2011
Posts: 16910


Report to Moderator

PostPosted: Wed May 25, 2011 12:34 am    Post subject: Re: Installation of Head Gasket Reply to specific post Reply with quote

I do a lot of 401-504 motors and what worked for me I made with some 3/4" od copper tubeing, I drilled couple small holes in the top of the tube so I can use a pic to pull them out I can post a pic of them if you like, have to be careful as they are soft but they work very well for me hope this helps cnt
 
Back to top
View user's profile
mEl
Tractor Guru


Joined: 28 Sep 1998
Posts: 6119


Report to Moderator

PostPosted: Wed May 25, 2011 2:56 am    Post subject: Re: Installation of Head Gasket Reply to specific post Reply with quote

Case Nutty 1660 wrote:
(quoted from post at 01:34:03 05/25/11) I do a lot of 401-504 motors and what worked for me I made with some 3/4" od copper tubeing, I drilled couple small holes in the top of the tube so I can use a pic to pull them out I can post a pic of them if you like, have to be careful as they are soft but they work very well for me hope this helps cnt


Gee guys, I have never used those and have never had any problems or associated failures. Certainly that is not said to criticise those who do. I hope that does not make me a bad mechanic. The firedam on the sleeve does a good job of keeping the gasket where it belongs and final alignment is done with the manifolds. I'll bet I'm not the only bad mechanic on here if that's the case. mEl
 
Back to top
View user's profile
Case Nutty 1660
Tractor Guru


Joined: 08 Mar 2011
Posts: 16910


Report to Moderator

PostPosted: Wed May 25, 2011 3:41 am    Post subject: Re: Installation of Head Gasket Reply to specific post Reply with quote

mEl if thats bad I must be rotten as I only made these "tools" in the last five years don't know that it has made a differance other than making me feel that their lined up better LOL cnt tom
 
Back to top
View user's profile
dboll
Guest






Report to Moderator

PostPosted: Wed May 25, 2011 4:46 am    Post subject: Re: Installation of Head Gasket Reply to specific post Reply with quote

made some on my lathe ,drilled and tapped them for 1/4 nc and remove them with long 1/4 bolts, I would hate to damage a fire ring if the gasket got bumped setting the head dowm.
 
Back to top
JW
Long Time User


Joined: 26 May 1998
Posts: 1136


Report to Moderator

PostPosted: Wed May 25, 2011 5:08 am    Post subject: Re: Installation of Head Gasket Reply to specific post Reply with quote

The only place those are really nice (but not a must have )is the back head on a 70 series with a cab. Its not real easy to see whats happening under the cowling.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters