Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

WD_45 Crankshaft Oil Seals


 
Post new topic    
View previous topic :: View next topic  
Author Message
Rock_Picker(MO)
Regular


Joined: 19 Dec 2007
Posts: 133


Report to Moderator

PostPosted: Tue Jul 12, 2011 2:00 pm    Post subject: WD_45 Crankshaft Oil Seals Reply to specific post Reply with quote

Is it worthwhile to replace just the lower part of front and rear seals? The rear seal is leaking a lot......running heavy oil, but it still leaks. Don't have time to remove engine this summer for a complete replacement. Comments appreciated.............RP
 
Back to top
View user's profile
JMS/.MN
Tractor Guru


Joined: 05 Mar 2009
Posts: 12827


Report to Moderator

PostPosted: Tue Jul 12, 2011 2:43 pm    Post subject: Re: WD_45 Crankshaft Oil Seals Reply to specific post Reply with quote

Not worthwhile to do half a job. Some years ago someone posted pix here of how to replace the rear main while in the tractor, using wire and two strips of plastic. I"m 2 states away from home now, so can"t send the link I printed out, but last time this happened, someone else did post a direct link, and the pix are in it.
 
Back to top
View user's profile
sprnt12
New User


Joined: 07 Apr 2011
Posts: 2


Report to Moderator

PostPosted: Tue Jul 12, 2011 3:17 pm    Post subject: Re: WD_45 Crankshaft Oil Seals Reply to specific post Reply with quote

Most rope seals can be replaced in the block with a tool from KD tools. It is a form of Chinese handcuff with a cable to pull the new one through.
 
Back to top
View user's profile
7030466
Regular


Joined: 27 Apr 2010
Posts: 22


Report to Moderator

PostPosted: Fri Jul 15, 2011 6:50 am    Post subject: Re: WD_45 Crankshaft Oil Seals Reply to specific post Reply with quote

Drop oil pan remove last main cap and unbolt or rotate top seal holder out install new seal.
 
Back to top
View user's profile
:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters