(800) 853-2651
SHOP NOW

Recent content by Brent grieves

  1. B

    RTU oil flowing out of magneto.

    Thanks for your help.
  2. B

    RTU oil flowing out of magneto.

    Thanks, these are the photos and I see nothing wrong with the passages, I can see all the way down in the crankcase, still not sure what the holes are for?
  3. B

    RTU oil flowing out of magneto.

    Thanks for the info, I’ll check it out. There is a hole that it looks like it drains back down to the crankcase have you ever seen that plugged? I was thinking about pouring some kerosene down through it.
  4. B

    RTU oil flowing out of magneto.

    Ill check out the passage ways, none of the manuals I have show the passages for the oil flow, I get about 25-30 lbs on the gauge.
  5. B

    RTU oil flowing out of magneto.

    Ill check out the passage ways, none of the manuals I have show the passages for the oil flow, I get about 25-30 lbs on the gauge.
  6. B

    RTU oil flowing out of magneto.

    IT Runs great, just after a while oil starts coming out of it. Thanks for all the info might have to bug you again. Ive done a lot of tractors but this is my first R . Didn't understand why they would have holes where the oil is supposed to come to.
  7. B

    RTU oil flowing out of magneto.

    Thanks, I will get out the JB weld.
  8. B

    RTU oil flowing out of magneto.

    They look like they are supposed to be there, but it doesn’t make since because of the oil that is pumped up to the mag drive?
  9. B

    RTU oil flowing out of magneto.

    Has anyone ever seen oil coming out of these holes in Magneto? On a early RTU
  10. B

    RTU oil seal in axel

    I got it off, turned it and put bolts from the inside and pushed it off, Thanks
  11. B

    RTU oil seal in axel

    I am having trouble getting this oil seal bearing holder off, the other side came right off it even had plugs you could take out and put bolts in to push it off, the left side does not. I can’t get it to budge at all. Any tricks? I need to get this seal changed. Thanks
  12. B

    1941 MM R

    That’s a good idea, with the hole in the bottom I really did not know why the need for a gasket. Thanks for the reply !
  13. B

    1941 MM R

    Thanks, I have talked with them at Welters, I don’t need to much it was pretty complete, just odds and ends.
  14. B

    1941 MM R

    I see that the newer ones have them but not sure about the older ones, is yours an early 40’s or one without the curtains? Some say no they don’t have them and some say they do so I’m guessing it’s a year thing, Thanks for the reply 😊
  15. B

    1941 MM R

    Very nice, I see it now I’ll make sure it’s clean and the put a new gasket on it. Great photos! Might I ask where you get most your parts from?
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top