(800) 853-2651
SHOP NOW

Recent content by GarryinNC

  1. G

    Disc Mower Curtain

    Try Hedgepeth Supply in Kentucky. link_disallowed
  2. G

    Allis Chalmers 5050 - a good tractor??

    Learn to work the independent pto properly.
  3. G

    Weld and recut brake drums?

    You are over thinking it.
  4. G

    Air compressor tank

    Very nice job!
  5. G

    Gleaners with 250 Chevy Engines

    Has anyone here ever put a Chevy 250 or 292 engine into a WC tractor using an adapter plate from a Gleaner combine powered by a Chevrolet 250 engine? What years/models of Gleaners used the 250 engine? Thanks. Garry
  6. G

    Question on Self propelled combines

    Thanks for the information on SP combines. I did know that they have a lot of belts! Garry
  7. G

    Question on Self propelled combines

    My question below on Gleaners with Chevy engines got me to thinking about how SP combines work. There is a gearbox and drivetrain. How is the separator driven? Does the separator have an in/out clutch? Have never had a chance to look at one. Garry
  8. G

    Gleaners with 250 Chevy Engines

    Was wondering if anyone knows what model Gleaners used 250 cubic inch Chevrolet engines and about what years they were used? A friend wants to put a 250 or 292 into a Allis Chalmers WC tractor and he was told that there is an adapter plate on the combines that mates the engine to an Allis...
  9. G

    Timing a Cub with dial indicater

    I believe that the spark plug hole is over the valves, as stated below. Garry
  10. G

    Gleaners with 250 Chevy Engines

    Thanks so much for the replies and photos. What he refers to may be the housing on the back of the engine that the sheave housing bolts to. Garry
  11. G

    Ford 3600 3 point won't raise

    Did the previous owner get the existing injection pump overhauled by a reputable shop or buy a new built aftermarket pump? If he bought new, is the old pump still around anywhere? Oops, posted this to the wrong thread. This post was edited by GarryinNC on 12/15/2023 at 03:33 pm.
  12. G

    273 knotter

    What are you going to do to the new pins to hold them in? Garry
  13. G

    Drill Press chuck

    Were you able to use your existing tapered mandrel? What did the tapers end up being? #3MT for the spindle and #33JT for the chuck? Garry
  14. G

    F2000 Remote Hydraulic connecting

    You may need a 'power beyond sleeve' in you loader control valve out port, depending on what valve you have. I ran into this on a 3930 tractor. Garry
  15. G

    Honda atv battery

    What relay terminals did you jump when you did the test?
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top