(800) 853-2651
SHOP NOW

Recent content by gary-ca

  1. G

    Magneto for a Cletrac F

    [thank you. I will call him tomorrow.
  2. G

    Magneto for a Cletrac F

    I am looking for a magneto for a Cletrac F. I have a Wico C mag that needs work and I don't think that is the correct mag anyway. What is the correct Mag and where can I get a good rebuilt one. Thank You, Gary
  3. G

    4610 Steerring leak at pitman arm

    My 4610 has oil seeping from the pitman arm. The parts manual shows two "seals" which I think are orings inside and 2 felt seals on the outside of the housing. Once the pitman arm is removed, is it possible to replace the orings without removing the steering shaft? Thank You for ideas.
  4. G

    4610 Steerring leak at pitman arm

    I found the parts. The pitman arm came off with a heavy duty puller and no heat. I replaced the 2 orings which were flat on inside and no longer soft like the new ones. Put on a new cover gasket with new washers for the banjo fittings . Put on 2 felt dust seals. Leak is stopped for now...
  5. G

    4610 Steerring leak at pitman arm

    I will get the parts together and update the outcome hopefully in a week. Thank You
  6. G

    4610 Steerring leak at pitman arm

    Thank You Bern, I wanted to have the oval gasket and seals for the banjo fittings on hand before starting the project. I was hoping I could get by the easy way so I thought I would ask. I will get a large pitman arm puller and give it a try. I tried previously but couldn't get it to move off...
  7. B

    Extreme Forestry Mulching

    Recently had a field cleared of some trees and autumn olives. Had a guy come in with a forestry mulcher - an amazing machine. The link is some video I took of the forestry mulcher at work. Forestry Mulcher
  8. G

    4610 Gauge Cluster Question

    Got it figured out. It was the alternator. It was charging the battery just fine but the power to the instrument cluster comes from the spade connector on the alternator. I think! I put on a new alternator and with engine running and key off the alt light comes on dim. The fuel gauge also...
  9. G

    4610 Gauge Cluster Question

    Sean, I knew what I meant. Ha Ha , yes, Rod used the correct terminology. Today I Tried a new oil pressure sender and hooked up an aftermarket gauge cluster. The new cluster fuel gauge was smoother than the original, the light still will not glow dim when engine running and key off. I...
  10. G

    4610 Gauge Cluster Question

    Hi Rod, Yes, that is what I am familiar with, the dim light glowing with engine running and key off. I think you may be on the right track with the grounding. I will do some tests; one test will be to run a dedicated wire from a good ground to the cluster ground spade. I will try other ways...
  11. G

    4610 Gauge Cluster Question

    Thank You, you cleared up some mis information I had. I will lower the fuel in the tank and see if there is any change in the bounce. I will look into the BG product for diesel. I can always try a new sender too. When I turn off the key and the engine is running, it does still charge the...
  12. G

    4610 Gauge Cluster Question

    Thanks for the reply. With the tractor running and the key in off position the light should glow, (I am pretty sure) I have a 4600 with the same setup. the 4610 used to respond the same way. I think it is a warning that maybe you accidently hit the key to the off position with your knee. The...
  13. G

    4610 Gauge Cluster Question

    I have a 1984 4610 with original gauge cluster. When running, the fuel gauge flickers and when I turn the key to off, the battery light does not glow as it should, I checked and cleaned all wires and terminals on back of cluster grounded the sender and got full gauge travel but when running it...
  14. G

    8N Axels too long?

    I always thought the tractor was cut down for use in narrow vineyards. I have another that is similar. The housing measures 42" from end to end and axels are 26 7/16". Were short axels and housings available?
  15. G

    8N Axels too long?

    Thanks for the replies. The tractor has 2700 hrs. and is in good shape. I will dress up the ends and reinstall. I think there is supposed be 2-6 thousands end play so I will see what happens. As long as both wheels don't turn the same direction when on jacks I guess it will last a few more...
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top