-
JJIM MN replied to the thread 4020 axle question.4010 axle diameter is smaller, so its housing is different than your 4020. Synchro - power shift housings would be the same. Yes, you...
-
JJIM MN replied to the thread Minneapolis Moline 2way plow.Good plow. Straighten trip and a little lub. It will work again.
-
JJIM MN replied to the thread Minneapolis Moline 2way plow.Straighten the trip. If have to clean off rust and little lub. It will work again.
-
JJIM MN replied to the thread John Deere 290 planter problems.Modify that mechanism, what ever it takes. The arm is too close to the trip lever. Must be wear that has let it get too close. Your...
-
JJIM MN replied to the thread New Idea Corn Pickers.2012, an old thread, but my thoughts?? Yes, for a mounted picker, the IH 234 has stripper plates to adjust to your ear size and no...
-
JJIM MN replied to the thread John Deere BR runs rough.Try fresh gas ; no ethanol, three or four gallons.. Pour in a can of Seafoam. Go use the tractor on a good pull to heat everything...
-
JJIM MN replied to the thread j d 830 belt pulley brake clutch.Parts catalog for the JD 830 offers both the facing D1932R and rivets or the clip on facing AB4748R.. Both will work just fine. You...
-
JJIM MN replied to the thread JD 720 Gas Compression test.Do as 620John suggested. If no leak into the cylinders, lub cylinder, new spark plugs and see if it will run?? Take it out and see...
-
JJIM MN replied to the thread Diesel Injector tester.Your local John Deere dealer or local diesel pump service shop.. They have a hand pump test stand to check your nozzles..
-
JJIM MN replied to the thread International 990 Swather.Ran a IH 990 for a lot of years.. A good machine, trouble free.. May have needed a guard, sickle knife, chain or belt,,, but the...
-
JJIM MN replied to the thread John Deere R starting motor.I-T No.-3, service manual for the John Deere R . Lead washers, crisscross pattern , twenty foot-pounds..
-
JJIM MN replied to the thread Model A pedestal dust excluder.A crescent shaped piece of heavy tin with a lip of metal to the top that is welded onto the top of the spindle. It is there to...
-
JJIM MN replied to the thread Jd 3010 gasser..Zenith carb has a round tag riveted in center to the top outside of the top half of carb. On tag is the zenith model no. , as model...
-
JJIM MN replied to the thread John Deere 3010 diesel.No pressure adjustment, you need to fix. Do a little trouble- shooting first.. Try bleeding your steering system first. The...
-
JJIM MN replied to the thread Jd 3010 gasser..Yes, do quick and easy checks first? Do you have the correct Zenith carburetor for a John Deere 3010? Is the load needle turned 1...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy