(800) 853-2651
SHOP NOW

Search results

  1. M

    New Welder

    Well, new to me. A few weeks back I bought a welder on a local online consignment auction. I was not able to go look at it, so I bought it sight on seen, not a good plan. It was part of an estate and I got it for under $200.00 so I took a chance. It's a Miller AEAD LE-200. A friend and I...
  2. M

    Fluorescent to LED.

    I have three fluorescent yard lights at the farm. It seems the bulbs have a rather short life. When I went to get a replacement at Home Depot, they didn't have any and the clerk referred me to a LED replacement. On the package it said in large print replaces large base fluorescents and sodium...
  3. M

    Addition to the Herd.

    Addition to the herd MF 275.
  4. M

    Unknown Ford tractor part

    Any body know what this is? It appears to be some kind of addon hydraulic valve.
  5. M

    New Steering wheel for MF 65

    I installed a new steering wheel from this site on my MF 65. I had to trim some off the bottom to clear the throttle, but that was pretty simple. The only difficult part is removing the old one, heat and persistence prevailed.
  6. M

    High/Low Jack

    My sons showed up yesterday and we kind of celebrated mother's day without her, first one. One had a black eye and stiches above it he had lost a battle with a High/Low jack handle. At the silo company we called them widow makers.
  7. M

    Loader Advice

    I recently acquired a MF 202 Work Bull. It came with a new Bucket that is somewhat over sized. I would like to install hay spears. The current loader has a loader arm spacing of about 32 inches on center. I would like to install some kind of quick attachment system. I was looking at a Titan hay...
  8. M

    1965 JD 4020

    I need to know the size of the bolts that hold the steering arm to the steering post. Dont ask. Thanks
  9. M

    Brake Story

    I stopped at a friends and he had his girl friends car on his hoist doing a brake job, 2014 Ford Fiesta. The pads were actual toast. We went to the parts store and got new pads but they didn't have the stainless steel inserts. When we went to install the pads they wouldn't go in. After...
  10. M

    Not the man I used to be

    I had to put a set of front weights on my gas 4020. With the ice on the farm drive the truck wont climb the hill with a load of round bales on the trailer. When i hooked the trailer on the three point, the front got light going up the driveway. I think they look better with the weights. I also...
  11. M

    Another Electric Puzzle

    The capacitor on the motor on my small auger went out (tab corroded off). I needed to grind feed so I hand started the 120 volt single phase motor. The motor started and the auger ran perfect, but no corn would come out of the auger. What's wrong.
  12. M

    Yanmar Experts

    I am helping a friend repair a Yanmar engine on a Morbark chipper. It has a damaged Turbo. The model number on the engine is 4019TF005 which I believe is a 4TNE84T-JS model. I have located a Turbo to fit a 4TNV84. Will it work? Comments regarding the correct turbo would be appreciated...
  13. M

    Time to Feed The Cows

    It started the second roll over. Good thing as the feeders were empty.
  14. M

    Trailer Adventure

    I had a little adventure picking up my MF 202 with a loader, which I bought last summer. I had driven it to my sons house in St. Johns. I borrowed my neighbors implement trailer, because it had it parked in the field I picked it up with my 3020 JD, I have a three point attachment with a...
  15. M

    2001 Silverado Brake Issue

    Got into truck to go to the farm. When I got to the of the end off the drive the ABS light came on. Drove to the farm and when I got out I could hear the ABS unit running with the key off. I pulled the fuse and it quit. If I put the fuse in the ABS unit runs continuously. The brakes work fine...
  16. M

    Re: Marquette Battery Charger

    Actually should be able to as it should have a circuit breaker. Probably took out the rectifier. A lot of the old style chargers use the same or a similar rectifier which is available on line. I replaced the one in my solar charger with a better design. I had previously replaced the diodes and...
  17. M

    70 Years.

    Born 70 years ago today in Owosso Michigan. Time sure flies. I don't feel that old. Is 70 some kind of milestone?
  18. M

    Re: Wife says I can build a hotrod if I sell most of my tra

    Some will most will not. Better add Hard Block.
  19. M

    2000 vs 2001 IH Loader

    I posted earlier this week regarding installing a IH 2001 loader on a JD 4020. I received responses which suggested that the IH 2001 was not strong enough for that application. After checking the loader I have discovered that it is a 2000. I am not familiar with IH loaders. Is a 2000 a lighter...
  20. M

    IH 2001 loader on 4020 JD

    I have acquired what I believe is a IH 2001 loader from a IH utility. I would like to install this on a 4020 JD. I will have to fabricate the mounting brackets and modify the loader frame. . I have some metal working skills, cut/weld etc. Has anyone done this? Pictures of brackets would be...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top