(800) 853-2651
SHOP NOW

Search results

  1. HFP

    Identify That Battery Charger

    Silver Beauty Industrial Battery Charger, Model 8250?
  2. HFP

    Mystery padlock

    It is for locking the dial on a rotary phone.
  3. HFP

    What else can you use a combine for?

    I've seen a few where people have put PTO snowblowers on the front in place of the header.
  4. HFP

    1946 JOHN DEERE LA rear plow attachment

    It looks like the operator's manual is DIR336 and is available for free download on the John Deere publications website. It looks like it has a few good pictures of the mounting. https://techpubs.deere.com/en-US/Search/Equipment
  5. HFP

    New John Deere 40 owner

    Knowing that the temporary goal is just to get it as a roller so you can work on it, could you use something like a SBPF206-20 bearing flange to replace your cast part and bearing to get it mobile and allow you time to find the right part or get yours fixed...
  6. HFP

    My latest "what is it" acquisition.

    I like to contribute to this forum, but don’t do so unless I’m darn near 100% sure my input is right. Based on what I found on this one, I was confident I had figured it out.
  7. HFP

    My latest "what is it" acquisition.

    Never played a round of tenis in my life. I “cheated” and used reverse image search and that led me down an internet rabbit hole where I found that eBay link.
  8. HFP

    My latest "what is it" acquisition.

    Part of a tool kit for spooling badminton and tennis racquets. Really. https://www.ebay.com/itm/364545127044
  9. HFP

    Can I put 730 LP pistons in a 630 engine?

    A 630 isn't a very common tractor for pulling due to the weight, but I'm sure you are aware of that. If you are going to spend the money to bore and sleeve it, I'd find a piston with more bore and compression than a 730. If you aren't going to stroke it, you will probably need to lengthen the...
  10. HFP

    Wartime front spoke wheel

    The group page is called "John Deere Unstyled A Row Crop Tractors". https://www.facebook.com/groups/294774371176911/posts/1332376594083345/?comment_id=1332379324083072&reply_comment_id=1332379777416360
  11. HFP

    620 Radiator Bottom tank on a 1955 60? Bad crack, need replacement.

    Looking at the parts book that is the correct bottom tank if your 60 has a pressurized cooling system. The cores appear to be the same part number (AA5582R) with either system.
  12. HFP

    Wartime front spoke wheel

    I posted a request on a John Deere A page on FB and did have an individual reply that has a pair of them for sale. If you use FB, I can contact you and share the link to that post and you can reach out to them. No idea on price, looks like location is Iowa.
  13. HFP

    unstyled JDA cam shaft removal

    MSD alluded to it. If you are going to replace the bearing anyway, you can just break it (good chance it will come apart anyway if you try and put a puller on it). If I remember correctly, the gear will clear the inner race. After the gear is off then you can heat, cut, weld on, or whatever...
  14. HFP

    John Deere B intake hose

    This info was off of the John Deere print for the part number. Material called out is SAE 20R2, Class R, Grade 2, Light Wall. It is possible one document or the other was updated over the years to make it common with something used on a newer machine. Either would probably work.
  15. HFP

    John Deere B intake hose

    According to Deere, B77R is 1.875 inch ID, 0.19 inch wall, 4.00 inch long.
  16. HFP

    Wartime front spoke wheel

    Do you know the part number of the wheel the hub came from?
  17. HFP

    Wartime front spoke wheel

    That sure looks like a cutoff and not a factory wheel to me.
  18. HFP

    H John Deere carb

    It has been mentioned, but I have had good luck with a little heat (not like heating a bolt) then a LH drill bit and small screw extractor.
  19. HFP

    Deere model A fuel pipe thread

    From what I see the thread callout on that nut is 1/2-24-N.S.-P.D.
  20. HFP

    4010 gas puller

    I can't answer you question, but posting this down on the tractor pulling forum may drum up a little more interest in this question.
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top