(800) 853-2651
SHOP NOW

Search results

  1. M

    Ford 555 water pump pressure

    Thanks again!
  2. M

    Ford 555 water pump pressure

    Hi Tom; does your operators manual also list the hydraulic oil type and the filter spec? My service manual covers both the 550 and 555 and lists oil spec as M2C48A and just says filter is 10 micron throw away. Just curious because I’ve seen other 555’s say oil spec is M2C134D although maybe...
  3. M

    Ford 555 water pump pressure

    I only went to the lower pressure cap as I have now taken the rad in for an internal external cleaning, replaced the water pump, put in a new thermostat and added the fan shroud that was not present, so I thought I would go all original. I haven’t tried it out yet however am hoping my...
  4. M

    Ford 555 water pump pressure

    Thanks again for the replies. Tropical was the problem so I got the right cap on order..
  5. M

    Ford 555 water pump pressure

    Just an update; So I went to order a 7 lb cap however they told me I need a 14 lb cap for the 1978 ford 555 tlb. Thanks Mike
  6. M

    Ford 555 water pump pressure

    Thanks everyone. Yes I meant the 201 cid 3.3 litre 3 cyl diesel. Thanks for the 7psi spec as mine has a 15psi cap on it. Was yours the same year? My service manual seems to list everything else however seemed to miss this spec. Also for the cost of the pump I think I’ll take your advise and...
  7. M

    Ford 555 water pump pressure

    Hello; I had some overheating issue with my 1978 ford 555 2.3 litre diesel. I wondered if anyone knew what psi this system should use for rad cap pressure as I can’t seem to find it in the manual ( if you’ve seen this in the 555 manual please let me know what page). I removed the thermostat...
  8. M

    Ford 555 front end

    Ok sounds good, this is just my standard email address so you can send it from any email and I will receive it (doesn t have to be from yesterdays tractor).
  9. M

    Ford 555 front end

    Hello; I have a ford 555 and the front casting of the nose has broken off where it bolts to the motor (part #d9nn3029ca) . I can get the casting for approx. $1300.00 however wondered if anyone knows what it would cost to install. It looks like you the rad, hydraulic pump, and axle would need to...
  10. M

    Ford 555 front end

    Hi Check Break. I was trying to private message you but it didn t work. I wondered if you could email me. My address is [email protected] . Thanks
  11. M

    Ford 4500 blocks

    Hello I have a 73 ford 4500 tlb with a blown block (201 cid diesel 3 cyl. # D0NN 6015 LA ). I wondered if a block from a 3000 diesel 175 cid (C7NN 6015 A) can be used with my head and pistons etc. to Make this a 201 cid.? It appears this block casting # could be used with 3000 or 4000 series...
  12. M

    Ford 555 backhoe brackets

    Actually found the original part # E1NNC585 BA connecting link. They don t sell it anymore so I ll have to search the wreckers
  13. M

    Ford 555 backhoe brackets

    Hello; I wondered if anyone knows where to find the lower right and left brackets below the axle for the backhoe to attach to, or what the part # may be. (Ford 555 1978). The upper mounts use the loader frame however the lower ones must be optional for a backhoe. Thanks
  14. M

    755 backhoe

    Hello; I have a 755 ford backhoe from a 1973 ford 4500 and wondered if anyone knew how much trouble it would be to fit to a ford 555? The 550 tractor lists this backhoe as an attachment but the 555 uses some other 15 backhoe. The 555 has a different style loader so I m not sure if I could...
  15. M

    755 backhoe

    From what I can tell all the hydraulic lines for loader and backhoe come from the front pump and into the subframe only of the loader/ backhoe as a reservoir. I m not sure if that front pump in front of radiator is original or if it was an add on however if I take the entire frame loader and...
  16. M

    755 backhoe

    Ok great thanks! So do you think my loader/backhoe subframe would bolt right onto the 545A ? It s hard to tell with just pics but I was hoping the two holes in the front would be roughly the same and I would forget about the original loader and use my old loader/backhoe subframe from my 4500...
  17. M

    755 backhoe

    Were there any models besides the 550 that this hoe would fit on, maybe a 455? ( I have blown my engine on 4500 and by the time I buy a new one and split the tractor to put it in etc. it may be cheaper to get a 455 or something and put my hoe on it) Thanks.
  18. M

    Ford 4500 blocks

    Rod blew and put about 2-1/2" hole through block just to the right of the oil filter. Still rotates etc. but I assume that would be unfixable. I could get the 3000 engine fairly cheap so wondered if that would work. I assume the block is same length and can be used with the 4500 but I m not sure.
  19. M

    Ford 4500 blocks

    Hi, yes this is a serial # from the engine C7NN 6015 a . I was thinking of using this engine for my blown 201 cid in my 4500 as a cheaper alternative so I was hoping it was a 192 but looks like your saying it s a 175 . Do you think this is too small for my 755 backhoe as I m just using on my...
  20. M

    Ford 4500 blocks

    Thanks everyone for the great replies. So does anyone know what a serial # of C33977 is in cid? Sounds like it could be either a 158,175 or a 192 cid. Thanks
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top