(800) 853-2651
SHOP NOW

Search results

  1. D

    Farmall M Disc Brakes

    I have a late M with disc brakes that I have problems with the brake discs glazing over. I take it apart and rough up the discs with sandpaper and the brakes work good for a short time. There is no oil leaking and the actuators, springs, and balls are all good and working. I swapped discs out of...
  2. D

    9N Smooth Axle

    Looking for a smooth hub axle. What are they going for?
  3. D

    8N Position Control

    I have an 8N that does not have a position control lever on the lift cover. There is no question that it is an 8N, 4 speed trans and 8N brakes. Has someone put a 9N, 2N hydraulic unit on this tractor? I don"t have it running yet so I don"t know how the lift functions.
  4. D

    2N GENERATOR CUT OUT

    What is the purpose of the odd shape of the generator terminal on the voltage cut out?
  5. D

    Interco R1 Tires

    Does anyone have any experience or advice regarding these tires?
  6. D

    190XT Powerdirector Problems

    When I turn the steering all the way to the left or right on my 190XT the tractor will stop just as if you put the clutch in. As soon as you turn the steering back the opposite way the tractor takes off again. It does this in both the low and high side. Other than when turned sharp the tractor...
  7. D

    JD 350C Reverser

    The reverser slipped on this tractor and was rebuilt replacing just about everything with new JD parts. It locks up fine now with no slippage but the rate of shift is way too fast. Is there any adjustment?
  8. D

    JD 350C Reverser

    I rebuilt the reverser that was slipping on a 350C. It works good now and doesn't slip but the shift is too fast and harsh. Is there an adjustment that controls the rate of shift from forward to reverse?
  9. D

    Ford 3000 Sheet Metal

    I am looking for the trim panels that cover the steering box on a Ford 3000. Any suggestions on where to start looking?
    • dhs
    • Thread
    • Replies: 3
    • Forum: Ford
  10. D

    JD 350C Ring and Pinion

    I am looking for a ring gear and pinion set for a JD 350C, good used or NOS. These parts no longer available through Deere and I haven't been able to find them aftermarket. Any and all leads appreciated.
  11. D

    4500 Transmission

    I need a couple transmission gears for a Ford 4500. They are NLA through CNH. I would take good used if anyone is parting a 4500.
    • dhs
    • Thread
    • Replies: 2
    • Forum: Ford
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top