-
O
Rearview Camera Recommendations on NH T4 100V
Good day, I would like to install a rear view camera. I have the bracket for the screen set up, but I am having trouble deciding the best placement for the camera. In looking at the attached photos, would you please suggest ideas on the best placement for the camera: Photo #1 rear of tractor... -
O
Lifting T4 100V with jack stands
I would like to lift my tractor so that I can work on it. I planned on lifting the front axle with a jack stand on each side. (see photo) Lifting the rear is a different story. The tractor is so narrow there is very little room for jack stands. A local Ford dealership recommended that I... -
O
T4 100 V Skid Plate
Last year while flailing in our orchard, I ran over a limb which ripped a hydraulic hose under the tractor. I am now trying to construct a skid plate. I have a few questions I hope you will answer. 1. I planned on using 3/16' steel plate. Is that thick enough? 2. I planned on installing a... -
O
Ford 2910 Hard To Start
Good day, I own a Ford 2910. I had to replace the fuel tank shutoff strainer because it became clogged. Then, after having cleaned the tank out and then using it for a period of several hours over days, it would not start. I again replaced the fuel strainer after finding it clogged. I... -
O
2910 Oil sending unit replacement
My tractor was leaking oil from the oil sending unit and the wire had come lose and was damaged at the spade connector. I installed a new oil sending unit but I am not able to reinstall the power steering case. The cover hits the oil sending unit connector. 1. The wire for the sending... -
O
Changing Oil Pan Gasket: Ford 2910
2910 leaking oil around the oil pan gasket. 1. Do you have to remove (lower) the driveshaft to replace the gasket? 2. If so, how do you do this? Is that a hole where you have an allen screw that needs to be taken out? (Please see attached photos) 3. What are the foot lbs for the... -
O
2910/776F front loader hydraulic cylinder rebuild
Good day, My 2910 has a 776f front loader. The lift cylinders are leaking and I would like to replace the seals. I have a few questions: 1. Since this loader cylinder does not have points to attach a gland tool and on each side of the cylinder is a flat area, do I just use a pipe wrench... -
O
Ford 2910 Hydraulic Lift Cover
Good day, I am trying to once in for all, with your assistance, trying to stop my hydraulic lift cover from leaking. I have replaced the o rings twice, but I still have the same problem. Any suggestions? Thank you, Rick -
O
Ford 2910 Headlights don't come on
Background: Removed headlights, took them apart, cleaned and painted them. Installed a new headlight switch that I bought on this site. Now, when I pull on the headlight switch the dash lights come on but neither of the headlights will come on. I checked the headlight switch fuse and it is... -
O
2910 Ford color codes
Good day, Would someone let me know the part# for Ford white on my 2910 tractor. Thank you, Rick- okgat
- Thread
- Replies: 2
- Forum: Tractor & Farm Talk
-
O
Ford 2910 fuel filter replacement
I have a Ford 2910. The fuel filter got clogged, so I need to replace it. I know they sell replacements of the type I need. But I was wondering if there was another way to replace it with a filter outside the tank. That way, it would be much easier to replace the filter in the future. Any... -
O
Ford 2910 Wiring Question
I have removed my dash to get to the fuel tank in order to clean the rust out. In doing so, I have found a red wire with connector disconnected from what I don't know. Would you please take a look at the photograph and if you know would you let me know where it plugs in. Thank you, Rick -
O
Replacing Vertical Muffler
I am not able to remove my vertical exhaust muffler on my NH 2910. I have tried heating with mapp and pulling on it for hours, its just not removable. I am thinking about cutting the muffler off above the hood where I can remove the hood. A friend has told me that cutting off the muffler... -
O
Bleeding Fuel Lines (NH 2910)
I own a NH 2910. I recently replaced the starter and in doing so, I had to unbolt the fuel filter bracket and a main line going to the fuel pump. When I finished installing the starter, I reconnected the fuel filter bracket and line and replaced the fuel filter. I attempted to bleed the... -
O
Ford 2910 Starter Problem or Solenoid?
I own a Ford 2910 tractor. About a year ago, I started the engine and the starter kept running. It got so bad that I had to disconnect the positive battery cable and it stopped. I looked around the generator/solenoid and saw that a spade connector had come lose from the solenoid. I... -
O
New Holland 2910 light switch knob
Good day, I have looked at my light switch knob and I find no way off removing the light switch knob. Are these pressed on? How do you remove it without breaking the knob? Thanks, Rick -
O
Ford 2910 Remote Hydraulic Leak
1) I have an 1984 2910 with remote hydraulics. Please see attached photos. It appears that I have a leak coming out around at least one bolt top center. Would you please give me some advice on how best to stop the leaking. 2)The placement of this remote was there when I purchased the... -
O
776F Front Loader for New Holland 2910
Regarding part number SML34225. The flexible drive shaft for my 776F front loader was destroyed. There are no replacements that I can find. The drive shaft is 13" long and connects to the hydraulic pump with shaft with a key-way. The other end of the shaft fits over a splined shaft. Any... -
O
Removal of exhaust
Good day, I have tried penetrating oil and striking the exhaust to remove it so I can replace with a new one. Does anyone have a fairly straight forward way of removing the exhaust on a Ford 2910 without having to torch it off. thanks.- okgat
- Thread
- Replies: 13
- Forum: Restoration Processes
-
O
New Holland 5030 Tractor Hours
I am looking at a 90's NH 5030 tractor. The seller is asking $7000.00. The tractor has approximately 6000 hours. Without looking into anything else, is 6000 hours too many hours to even consider when purchasing a tractor. thank you, Rick.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy