(800) 853-2651
SHOP NOW

Search results

  1. P

    Need a hexigon shaft for AC disc

    Hi, All. I need a 84 inch hexigon shaft for my AC disc. Point to point at 180 degree measure is 1.25 What type of steel are these made out of? Have found some supply houses that have the rod in stock but only up to 6ft. I have a very good welder man that can do the welding.
  2. P

    JD 440 ic bottom rollers

    I bought a 1959 JD 440 oc took it to my mechanic that only works on crawlers and skidsteers He said the bottom rollers look good except for one that should work but should look at replacing it or maybe all of them on the one side Final drives are good, bands are new, motor is fine as are...
  3. P

    JD 440 ic 1959

    Hi all again. Thanks for all the info. I have owner's and service manual on order. I would like to change all fluids while waiting for those manuals. Am I correct in thinking that the hydraulics and transmission use the same type of oil, like the n series tractors? What bout the motor? 15...
  4. P

    JD 440 crawler

    I just purchased a 440 crawler and have a few questions. Does the idler wheel assembly just slide on the metal frame? One side the The tract is too tight. Can I let some grease out of the tensioner? If I can How do I do that. How do I grease the rollers. It has the rock guards on it? I know...
  5. P

    Stihl chainsaw hard strart

    I have a Stihl chainsaw that takes about 8 pulls to start. Used to be about 2-3 when new about 5 yrs ago But once started runs fine and I can run it dry, refill and one to two pulls we are up and running. I was thinking of buying a new carb but just don't know. 026 farmboss Thanks to...
  6. P

    anyone by 1690 W Storey Rd, Casa Grande, AZ 85194, USA

    Is there anyone on this site that is close to 1690 W Storey Rd, Casa Grande, AZ 85194, USA ROBERTS TRACTOR CO. LLC I am looking at a certain tractor there and would like to have someone check it out for me.
  7. P

    NH and Fergy parts

    I am wondering if anyone would be interested in some new nh rock guards for a sickle mower and also 2 sickle bars for a NH haybind no welds. I am in the process of cleaning out my brother's garage and am finding a lot of new and used parts. also have a good genny for a Ferguson TO 30 Some...
  8. P

    48 *N skips at high speed

    Hi, All. I have a 48 *N Ford. It starts right up no issues. However at high speed there is a definite skip/miss and it seem under power. No back fire. New plugs/new filter/checked screen in carb/great gas flow. checked spark on all plug/ Bright yellow and large. New coil/points/condensor
  9. P

    Swapping engines in Husquvarna rider

    I have a Husqvarna riding mow with a twin Kawasaki engine on it. Last night it started to rattle and blew some smoke out the muffler and I shut down. No oil leakage and oil is where it should be on the dip stick but I think it is gone. Just changed oil and filter about 12 hrs ago. How hard...
  10. P

    8n starts then quits after about a minute

    I have an 8n 74/48 yr. Was running rough and backfiring. So i changed the plugs/wires/fuel filter IT would start then quit running after about a minute. No amount of grinding on choke would get it running of sputter even. So I changed the points and condensor as it has been awhile. Started right...
  11. P

    8n leaking oil from top of filter cap

    I changed the oil and filter on my 8n numerous times. But this time I have a leak on top of the filter cap. At first it appeared that maybe it was not tight enough so I just snugged it up. Same issue. It has a gasket underneath the bolt head. Did I miss something this time?
  12. P

    Valley Industries Sprayer wand

    I am wondering if any of you have a valley industries sprayer wand that you ave repaired with new rubber o-rings. I have one that I thought I could do that to. The only problem is that now I cannot figure out how to put back together. it has a ping with a pivot hole on one end that sames to...
  13. P

    TO30 no spark

    Hi, all My brother has a to30 with a 12 volt conversion but he kept the 6 volt coil with a rectangle resistor. It was running fine for yrs (8) he parked it yesterday and now wont start. I replaced all the spark plug and distributor wires as they were corroded. Same issue. Checked voltage to...
  14. P

    double wide hay rake

    I am trying to help my younger brother with a problem he has with a used Heston double wide hay rake. It will pick up the rows nicely for about 100 to 150 ft then just skim along the top of the rows. We have tied adjusting the angle of the wheel bars, the width of the row intake. He is...
  15. P

    SImple wiring of BS motor

    Can anyone help with how to wire the following B&S engine? model 311707 type 0138-E1 code 010228ZE I have the whole harness but just want a basic wiring diagram. It has the fuel solenoid. Want to use on a stationary platform.
  16. P

    8n Front mount distribitor 6v

    I have an early 8n. Still six volt. I rebuilt the steering so with I had to remove some wires. I had marked then all. Bought a new 6 volt battery. Got everything back together. Double checked wiring against manual. No spark. Then the wire that goes from the terminal block (has other wires...
  17. P

    AC 611 LT

    Where can I get the plastic nose piece for this tractor?
  18. P

    AC 611 LT

    AC 611 LT I had to remove the shift lever to install a new oil gasket and now the tractor seems to shift differently. It seems to have more travel when shifting inot 1st and 3rd. I thought all I did was pull out the lever.
  19. P

    48 8N rear hubs/axle

    I have an oil leak on the right side rear. I have replaced the hub but the old one looked just fine. The seals look good except the one under the washer before the axle nut. When I compare the lenght of each axle protruding from the nut, they are not the same. The left side has 3/16 inch and...
  20. P

    Thanks for the misfire help

    Thanks to al for the misfire help. I changed plugs and it ran well. I also replaced the wires as it was a easy replaced item.
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top