-
113fx replied to the thread Intermittent spark from magneto.I am sorry for the confusion. I should not have been saying spark most of the time. Often when I am talking about spark it is the flow...
-
113fx replied to the thread Intermittent spark from magneto.I was intrigued by your answer. So I went out to the shop and hooked up my timing light to the #2 wire. While it was still attached to...
-
-
113fx replied to the thread Intermittent spark from magneto.I'm fairly certain I have this magneto squared away, but I can't imagine this will be the only magneto tractor that I see down the road...
-
113fx replied to the thread Intermittent spark from magneto.I wasn't planning on spending half of a day rotating a motor I honestly thought it was going to be as simple as cleaning the point gap...
-
113fx replied to the thread Intermittent spark from magneto.Sure does, but than I would have most likely stumped myself as to why I couldn't get spark at all and would have unnecessarily torn the...
-
113fx replied to the thread What gleaners had the a/c 262.Ok thanks
-
113fx replied to the thread Intermittent spark from magneto.When I checked, the timing was around 7.-10. past TDC. I now have it timed for TDC as per the manual. Now the manual says to set it at...
-
-
1Currently have a D19 with a dist rotor that is so worn out I can move almost an 1/8" either way. Not looking to buy a new on, or have...
-
-
113fx replied to the thread Intermittent spark from magneto.Not yet, just wore my backside out turning that hand crank. #1 on the dist cap is the only one that won't fire yet, and it won't do it...
-
113fx replied to the thread Intermittent spark from magneto.Ive disconnected the wire now and, it sounds like it trips twice on every full rotation without fail. After working on this a bit more I...
-
113fx replied to the thread Intermittent spark from magneto.Thanks for the link. So far dragging the points with a file did nothing. I decided to change out the shutoff wire real quick since it...
-
113fx replied to the thread Intermittent spark from magneto.Points looked good, but drug the file over them anyway. The gap is .014 so I feel good about that. As I'm putting the cover plate back...
-
-
1This W4 is the first magneto tractor I've ever had. I figured since I'm waiting on carb parts I may as well see where the timing was on...
-
113fx replied to the thread D19 distributor.Rebuilt cost $450+ core + shipping. The rebuild parts for me to do it myself are $250. The guy who quoted me the prices told me even...
-
1Currently have a worn out distributor on my D19 and am going to look for a replacement. My most likely source out here I think is going...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy