(800) 853-2651
SHOP NOW

Recent content by 1badMF

  1. 1

    low oil pressure after overhaul

    I talked to the mechanic and I think we're going to replace the oil pump. He is telling me that particular motor doesn't have cam bearing and the cam was checked by the machine shop.
  2. 1

    low oil pressure after overhaul

    I don't think the kit came with cam shaft bearings. I know he replaced the main bearings for sure
  3. 1

    low oil pressure after overhaul

    15-40
  4. 1

    low oil pressure after overhaul

    Thanks for the quick replies. Would it be safe to operate with the gauge reading like it is with the needle being on the low/good line? Also the gauge was about 12 o'clock while it was idling and I first started working. Then dropped after a half hour or so. It was doing this same thing prior...
  5. 1

    low oil pressure after overhaul

    I picked up my tractor today after the motor overhauled. The tractor is a 1961 MF 35 with the perkins diesel. The motor was pulled and completely rebuilt with all new bearings, pistons, ect. The tractor idled for about 15 minutes then I hooked up a bush hog and began to do some mowing. After...
  6. 1

    Rhino se5 rotary cutter

    Thanks!
  7. 1

    Rhino se5 rotary cutter

    Does anyone have any specs on this mower? Specifically the size of gearbox, weight and size of brush its capable of cutting?
  8. 1

    Injector pump

    Thanks. I'll give you a call this afternoon. It'll be from an 843 area code.
  9. 1

    Injector pump

    Diesel is there a way I can contact you about this?
  10. 1

    Injector pump

    I have recently had the engine in my Massey 35 completely overhauled and as the mechanic was putting it back together he seems to think there is an issue with either the injector pump or injectors causing it to run lean which lead to the original problem of burning a hole in a piston. He is...
  11. 1

    MF 35 rebuild guidance

    Thanks for the replies guys. I reevaluated today. It fired right up but had some smoke coming from the exhaust. Oil pressure was good. Pulled the dip stick and a little smoke came out and oil was bubbling out. I didn't try to drive it or put it under a load. I figured that was all I needed...
  12. 1

    MF 35 rebuild guidance

    I purchased a 1961 MF 35 with the Perkins diesel with 2200 hours about 2 months ago. I've used it 8-10 times pulling a 5ft disc harrow and noticed the oil pressure drop to just barley in the green. After doing a quick search it appears the bearings are worn and I am going to need to rebuild...
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top