Recent content by 20MuleTeam

2
Free U running

Grandson on junk yard U.
- 20MuleTeam
- Post #1
- Jun 9, 2020
- Forum: Minneapolis-Moline
2
one man show

No quitter
- 20MuleTeam
- Post #1
- May 18, 2020
- Forum: Tractor & Farm Talk
2
one man show

Nice cat.
- 20MuleTeam
- Post #1
- May 18, 2020
- Forum: Tractor & Farm Talk
2
fishing line old fashion for cane pole

WalMart?
- 20MuleTeam
- Post #1
- May 14, 2020
- Forum: Tractor & Farm Talk
2
Allis g

My '50 G @ work.
- 20MuleTeam
- Post #1
- May 5, 2020
- Forum: Allis-Chalmers
2
Repowering M, with 400 engine

2" stroke would be a good idea, maybe?
- 20MuleTeam
- Post #1
- Mar 28, 2020
- Forum: Tractor Pulling
2
Fifty years ago today.

Yes. National cemetery @ Ft Jackson, every grave gets a weath every year. Been going every year, everyone gets to place a wreath on one of the 5000+ graves.
- 20MuleTeam
- Post #1
- Mar 25, 2020
- Forum: Oliver, Cletrac, Co-op and Cockshutt
2
Fifty years ago today.

Seems like yesterday!
- 20MuleTeam
- Post #1
- Mar 25, 2020
- Forum: Oliver, Cletrac, Co-op and Cockshutt
2
Fifty years ago today.

I was there in 1970, 50 yrs ago. Here I am with my 94 yr old neighbor, WWII & 3 tours in Nam 101 1st ABN.
- 20MuleTeam
- Post #1
- Mar 24, 2020
- Forum: Oliver, Cletrac, Co-op and Cockshutt
2
Cubic inch formula

If you could measure and divide perfectly, you would get 3.141592653589793238..., or pi. Only difference would be where pi is rounded to - 3.14 or 3.1416 or ??.
- 20MuleTeam
- Post #1
- Nov 20, 2019
- Forum: Tractor Pulling
2
Cubic inch formula

Yes. Area of circle is 3.1416 * diameter * diameter divided by 4. (3.1416/4 = 0.7854) Then * stroke * number of cylinders
- 20MuleTeam
- Post #1
- Nov 19, 2019
- Forum: Tractor Pulling
2
JD70 gear ratios

Yea, Never found much use for 4th gear, geared too high for most chores, throttle back & not enuf power becomes an issue.
- 20MuleTeam
- Post #1
- Sep 29, 2019
- Forum: John Deere
2
John Deere B 1948 Mild Pulling Parts Wanted

Thanks!
- 20MuleTeam
- Post #1
- Jul 21, 2019
- Forum: Tractor Pulling
2
pto

Went to a pull where the pto cover had to be "OEM'- asked head man what was their intent for this rule, said he didn't know.
- 20MuleTeam
- Post #1
- Jul 6, 2019
- Forum: Tractor Pulling
2
Tractor Pull

Can't wait, got the G ready.
- 20MuleTeam
- Post #1
- Jul 3, 2019
- Forum: Tractor Pulling

Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy