Recent content by 2MaineFarmers

  1. 2

    NH 311 Baler, cracked/broken knotter.

    Thanks. I looked more and a new one FULLY DRESSED is $1300. New one bare is $350. There are a few on ebay that are dressed for around $300. I think I will go that route and put a few of my newer parts on it. Found a decent write up for changing it out on Hay Talk. I'll make sure the adjustments...
  2. 2

    NH 311 Baler, cracked/broken knotter.

    I was cleaning out the knotters today to grease before baling and saw that one of them has multiple cracks going through it. I had hay raked and no choice so figured I would start baling and see what happened. Made 441 without missing a knot. Which is great because otherwise I would have lost...
  3. 2

    HELP! NH 311 baler bound up in feeder. Fixed but now won

    Thanks for the encouraging words, gents. Picked up some parts today and when I was scouring parts diagrams on messicks I saw my feeder bar has always been missing the hard plastic end caps on the little bearing/wheels that run in the tracks. My tracks are getting worn and looked like they were...
  4. 2

    HELP! NH 311 baler bound up in feeder. Fixed but now won

    Thanks all and John, you actually kind of predicted my second and third break down in 2 days. What a tough 24 hours. SO to give a small update, it looks like my main knife caught the guide bar and basically everything went to hell. I bent everything back, including pulling the guide bar out and...
  5. 2

    HELP! NH 311 baler bound up in feeder. Fixed but now won

    So I figured it I bound it it with the prybar I might be able to free it that way. And I did. So I tried it out and it bound up again. When the big main knife closes its getting hung up on something. I think that's how my aluminum tines got so bunged up. I'll turn it by hand and see if I can get...
  6. 2

    HELP! NH 311 baler bound up in feeder. Fixed but now won

    Now that I think about it, it WAS working fine. I wanted to see if I could back the arms out a couple inches so I went to turn the flywheel. First I turned it the wrong way and it traveled easily and moved the arms half an inch forward. Then I couldn't muscle it backwards at all so I put a...
  7. 2

    HELP! NH 311 baler bound up in feeder. Fixed but now won

    It looks like my feeder tooth spring broke and when it traveled back to shove hay again, the tine came up over the guide bar and wedged on its way to push. It scored up the aluminum feeders and bent one all to hell. Not exactly sure how that happened. I bent everything back and threw an old...
  8. 2

    New Holland 90hp Blue smoke at high rpm - NO LOAD only

    After ~25 hours of run time the oil level is perfectly between the high and low marks, which means it's down 1.5 quarts from full. I did put new air filters on it last fall. No change. Fuel filter looks like it's pretty new but I will change that before too long. Being a 2008 I believe...
  9. 2

    New Holland 90hp Blue smoke at high rpm - NO LOAD only

    I have a fuel filter on the shelf so I can do that. I did oil and filter changes shortly after I got it last year with no change. I'll put that on the list for next weekend. It is a 4.5L 4 cylinder turbocharged diesel. Oil level has stayed pretty consistent, but doesn't look a lot thinner. I...
  10. 2

    New Holland 90hp Blue smoke at high rpm - NO LOAD only

    2008 NH T4050. Tractor starts up as soon as you touch the key. Idles great with no smoke at all. As RPM is increased, let's say over 1500, blue smoke starts to roll out. If the tractor is sitting at 2300rpm without a load, it's blowing enough smoke to really choke you out. Almost as blue as the...
  11. 2

    NH 311 Baler, pickup weak from getting stuck on a hump

    Thank you all. I will investigate and report back with whatever i find. Hopefully this weekend, but it seems every time i cross something off my list, two more get added back on.
  12. 2

    NH 311 Baler, pickup weak from getting stuck on a hump

    Hi Folks, Hope those of you that are able to stay home are getting an early start to equipment prep. That is what i've been up to and I wanted to get a little advice before I try to tackle my baler. The last field of last season has a hump running down it and i can usually rake to...
  13. 2

    NH 311 twine pulls out of holder on one side

    Central Maine, about a half hour west of Augusta. I hoped to be doing second crop by now but it was just too wet to get on the fields in june.
  14. 2

    NH 311 twine pulls out of holder on one side

    Thanks, that is exactly what I did. I actually hooked up my little 15 horse tractor to the baler, broke up a bale and threw it in. Surprised me that it didn't bother that little tractor at all. Everything seemed to be in working order so I ran it yesterday and did 676 bales with only missing...
  15. 2

    NH 311 twine pulls out of holder on one side

    Took me about 6 hours but I changed out the twine holder on the problem side (what a pita!) adjusted twine disc timing on both sides and when I tripped the knotter and checked everything, the needle on the problem side needed to be adjusted both up and over. So fingers crossed, we will see how...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top