(800) 853-2651
SHOP NOW

Recent content by 2wheelgnnr

Yesterday's Tractor Forums
  1. 2wheelgnnr

    Ford Jubilee is there a Starting point for the idle screw on carb

    I will double check but I swear I dont have a third Idle speed adjustment stop screw. Huh ok right outa the manual...who da thunk...... I never thought to dig of my manual...man im ignorant at times!! I will also pull out my Ford manual and put and keep in my Tool box!!
  2. 2wheelgnnr

    Ford Jubilee is there a Starting point for the idle screw on carb

    ok GOT it....will try that and go from there.....Thank you so much!!!!!
  3. 2wheelgnnr

    Ford Jubilee is there a Starting point for the idle screw on carb

    Also not 100% which screw does what they both labed idle screw on some diagrams Ive seen..........Im thinking there would be a gas/air mixture and a idle screw??
  4. 2wheelgnnr

    Ford Jubilee is there a Starting point for the idle screw on carb

    OK I think I screwed up my carb settings to the point where she wont start or stay running...starts up but cant sustain so dies. Is there a starting or stock settings to start from in tuning the carb. LIke .... screw all the way in and back off 2 1/2 turns to start... adjust from there...
  5. 2wheelgnnr

    Ford Jubilee Surging idle resulting in bucking

    help me identify these two adj. The thumb screw says the main adj. air / fuel?? but not sure what the second smaller screw it for. idle??? I found this for a starting point: To properly set a Marvel Schebler stock carburetor, follow these guidelines: Initial Adjustments Start with the...
  6. 2wheelgnnr

    Ford Jubilee Surging idle resulting in bucking

    ok now Ive screwed up the carb setting enough it wont start....is there a beginning settings for the air fuel mix screws like vw has.........like screw it all the way closed or till stops then screw out 2 1/2 turns..and start there.........I will play with more tonight and debris is always an...
  7. 2wheelgnnr

    Ford Jubilee Surging idle resulting in bucking

    ok I will make sure this time I clean up the carb I do that. my float was sticking closed so I was not getting fuel and starving in my situation....... but a new carb fixed that. ( I would clean up float and in a couple months would happen again so just finally got new carb) but...
  8. 2wheelgnnr

    Ford Jubilee Surging idle resulting in bucking

    Hmmmm yeah rev up and down...will go and sputter a LITTLE less in high gear across the lawn/down the road She seems to be burning a lot of oil lately...or maybe too rich......I have not pulled the plugs I will do that tonight and see if they are all carboned up. if thats the case too...
  9. 2wheelgnnr

    Ford Jubilee Surging idle resulting in bucking

    Ford Jubilee....I sort think I know my problem but want to make sure nothing else. She bucks and idle surges up and down...like it running out of gas..sputtering and that....now to add to it I have had issues with the carb float sticking on me. I though I had if fixed but could this be a...
  10. 2wheelgnnr

    Ford Jubilee Govenor and Choke Hookup to Carb????

    found it..I got the rods backwards........
  11. 2wheelgnnr

    Ford Jubilee Govenor and Choke Hookup to Carb????

    ok my carb has a sticky float. I took it off in the fall to fix it and whatnot. now hooking it back up Not sure how the choke and govener rods hook up to the carb.....I think I have it wrong as I have the choke rod connected to the Top stub ( butterfly ) and the lower govener rod from the...
  12. 2wheelgnnr

    Iron Oak Brush Boss 2000 Wood chipper

    reached out to them.....They cannot provide a manual on that product...damn...so Im searching to see where else or what else i can find on it. Have to start stripping it down to check the condition of blades... Thanks
  13. 2wheelgnnr

    Iron Oak Brush Boss 2000 Wood chipper

    Ive reached out to Iron & Oak to see. I got the model #. BHSC-CM28. They are only making Log Splitters now...so we will see. An internet search on them has not turned up too much. But we will see.
  14. 2wheelgnnr

    Iron Oak Brush Boss 2000 Wood chipper

    Not necessarily a tractor implement but I just acquired a Iron & Oak Brush Boss Wood chipper BIL says can eat up to 3". I dont think that old but iron & Oak only does Log splitters now. Anybody know anything about this. has a cast iron Briggs & Stratton 8hp motor. I dont see a...
  15. 2wheelgnnr

    Leaking Hyd Fluid From Weep Hole? I thought I saw a post

    True will do...maybe depending it looks Replace it anyways for good measure....good point thank you for pointing that out.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top