(800) 853-2651
SHOP NOW

Recent content by 36b A

Yesterday's Tractor Forums
  1. 3

    #60 4 bolt plow shares

    Thanks guys parts are on the way
  2. 3

    #60 4 bolt plow shares

    Had to get down further here's the moldboard number and short brace brace
  3. 3

    #60 4 bolt plow shares

  4. 3

    #60 4 bolt plow shares

    I did have but I'll get more when I get to work . Someone sprayed something on them can't read anything on the backs .
  5. 3

    #60 4 bolt plow shares

    These holes don't measure the same as your picture . Unless it's a 16 inch
  6. 3

    #60 4 bolt plow shares

    I can't read anything on the back saying super chief or other .
  7. 3

    #60 4 bolt plow shares

  8. 3

    #60 4 bolt plow shares

    Looking for plow shares and the number is kinda messed . Looks like 04 14 -4 or 01 41-4 hard to tell . This don't match any number in shoup catalog . There number is R44144 . I don't want to order them for a customer and have to return them if not right .
  9. 3

    1460 mower conditioner timing turtles

    Anybody have any wisdom or secrets to share on how to time the turtles ? Bearing went out on the first one and it was just taken apart !
  10. 3

    Pete's gone

    I just started to see his videos . Well there are plenty to look through .
  11. 3

    Hard throttle on a 400

    Have a 400 gas with a M&W governor . when moving the throttle lever with the motor not running it moves like normal . There is no binding . but with it running you really got to pull on it to get to wot . I had a super m with a rocket on it and it didn't do that . Any ideas to look for ?
  12. 3

    400 project tractor

    It's not that it's more in the dash area now that you said that . I'll pay more attention to it next time I start it .
  13. 3

    400 project tractor

    Nothing to worry about them ? Sounded like a spun bearing on a shaft .
  14. 3

    1936 unstyled B newbie question

    I'd dump the antifreeze in a bucket to ensure proper mixing . Then test the mix for 50/50 or so being your in the South not in Minnesota . Some new cores do have thinner tubes like stated and could be the gauge . If it's not steaming or boiling not a big deal till you want to work it some .
  15. 3

    400 project tractor

    Haven't run my 400 in a few months so I fired it up the other day . When it started it made a short funny noise like a dry bearing . Zing and that was it nothing else and ran fine . Anybody have this ?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top