(800) 853-2651
SHOP NOW

Recent content by 39wc

Yesterday's Tractor Forums
  1. 3

    WC fenders

    Steiner Tractor Parts has new reproduction styled fenders $175 each.
  2. 3

    WC Shift Handle Removal

    Can anyone give me some advise as how to remove the shift handle out of the shift tower on the transmission. I removed the snap ring and washer, disconnected the short rod from the trunnion for the reverse lock out. Do I just pull it straight up or do I need to do something else? Does it slide...
  3. 3

    D14 steering

    I believe he is referring to the Char-lynn torque generator as the inline power steering. Steiner has them as well as many other suppliers. Just add a GM power steering pump to supply fluid to the char-lynn torque generator and your good to go.
  4. 3

    Freeman farm loader

    I use two garage door springs on my trip bucket.. Works like a champ. They come in different lengths and tensions too.
  5. 3

    allis WC axle seals

    Try your local Agco dealer. Mine had them in stock and yes they are rubber now. Originals were made of cork.
  6. 3

    wd hard to steer

    Sounds like the bearings are bad on your worm gear shaft inside your pedestal. Not a terrible job to replace.
  7. 3

    allis WC axle seals

    How big of a job is it to replace the inter seal??
  8. 3

    AC B v8 Pictures

    I likey!!! Keep the pics coming. Any chance you could show some pics of your bellhousing and how you adapted it?
  9. 3

    Power Steering on a WC

    Already have the Saginaw power steering pump laying around. Would have to scrounge up the wd-45 power steering pump. Beside the Saginaw is smaller and easier to hide I think.
  10. 3

    Power Steering on a WC

    Have a thought to put power steering on the old WC. Thinking of using a double groove pulley off a WD-45 to spin a "75 chevy truck power steering pump. Wich in turn will supply fluid to a Char-Lynn Torque Generator. Any reason my thinking is wrong? Or will the pump supply to much pressure? Any...
  11. 3

    WC sale

    Yes that would be an easy mod to do especially with the 2 grove crank shaft pulley I have.
  12. 3

    WC sale

    I have a paulson loader on my WC. Hydraulics are run off the PTO via Charlyne power pak. Been thinking also of making a front mounted hydraulic system since I have a 2 grove belt pulley off a WD45 to run off the crank for live hydraulics. jeff [email protected]
  13. 3

    WC sale

    Can you post some more photo"s of your 3 pt set up. I have been considering making one for my "39 WC as well. Thanks.. jeff
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top