(800) 853-2651
SHOP NOW

Recent content by 4020guy

Yesterday's Tractor Forums
  1. 4

    190 XT series?

    The series II and III's had no bars across the grill and flat top fenders similar to a IH. They also had larger axels and 4 pinion differentials. The first ones were called the bar-grills and had fenders that kinda ran to the platform on the front. They had a 2 pinion diff and smaller rear axels...
  2. 4

    Lincoln 225 Wiring

    Neighbour decided to blow out his welder. Only didn't remove wires from the on/off switch before removing the cabinet and broke the old fibre backing on the switch. He removed the switch and didn't mark the wires going to the primary coil. Dumped it off here and I replaced the switch with a 50...
  3. 4

    Starter fertilizer help!

    Find out the weight per US gallon, probably around 13 pounds, multiplied by say 5 gallons per acre gives 65 pounds of 3 18 18 or 3 percent N equals 1.95lbN, 18 percent P2O5 and K2O equals 11.7lb each per acre.....Ron
  4. 4

    ? for DeltaRed

    A 269 is a long tongue 268, 3 joint pto rather than a 2 joint. A 272 is a engine drive 268. A 275 is a much better heavier built 268. The 268, 269, 272, 275, 273, 310 all use the similar retractable feeder carrage. The 65 used something the same.....Ron
  5. 4

    White 5100 Planter

    What would a 5100 be like for soybeans? Are they much different than a 6100? How are the parts availability? This one is a 12row- 30inch with no fertilizer. Just wondering?.....Ron
  6. 4

    Tragic Accident- Be Careful Out There

    Yesterday a 69 year old dairy farmer 35 miles from me lost both arms in a pto accident. I knew him quite well and had sold him bred heifers in the past. He farmed with his son on a 5th generation farm. Before I knew him, he had lost a foot in some other farm mishap as well but one would never...
  7. 4

    valve stem hole

    Like Bill says, I use 2 5/8's flats brazed together. I then grind 2 sides off and cut a hole in the rim where the original flattened place with the hole was. Grind it after welding and you'll never know it was repaired...Ron
  8. 4

    Tired of math questions

    492- New Holland Haybine, 357-New Holland grinder mixer, 816- New Holland forage box. Just sayin....Ron
  9. 4

    Royal Purple Motor Oil

    Would Royal Purple API say 10W40 be a good choice for small 4 stroke engines? Have some 5hp Hondas and a 23hp Kawasaki in a JD 320 lawn mower. I use JD Plus 50 15W40 in most everything else. Just wondering.....Ron
  10. 4

    4020/3020 question

    4020's were upgraded to 4230's@ 100 PTO hp. The 3020's to 4030's @ 80 PTO hp.....Ron
  11. 4

    4400 unload auger

    Hope it's not the bearing in the drive on the engine or the splines on the flywheel. With the mill engaged the drive may not be turning so no unloading auger turning. Does the combine move ok? Keep us posted. Good luck....Ron
  12. 4

    Canada sucks!

    Hey Gordon Lightfoot is Canadian...Ron
  13. 4

    1020

    The friction disks are part number T22696. I put some on a 2120 a couple years ago and they certainly were a lot less than that maybe 15 or 20 bucks. Take the hand throttle and remove the roll pin below the disks and make sure the piece that compress the friction disks are free to move up and...
  14. 4

    1966-67 510 (Lanz)

    As for tires, probably 14.9x28. Very low capacity, limited rudimentary hydraulic system. Power assist steering an option. Ten speed transmission with a two stage clutch. The engine is the best part, a 3 cylinder 151 cu. in. similar to a 1020. Oil bath air cleaner. Some tractor parts no longer...
  15. 4

    John Deere 7020 help.

    The right person can get a lot of use out of this older stuff. Depends a lot on the amount to do and the time to get it done in. If one uses a lower gear or a little smaller implement it makes a big difference. Starting with the disc or cultivator or plough out of the ground and dropping it when...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top