(800) 853-2651
SHOP NOW

Recent content by 41Frank

Yesterday's Tractor Forums
  1. 4

    Before and After of 1960 JD 435

    Very nice job! Since you are broken in on working on 435s, I will bring mine over for you. I replaced the steering knuckle and pins and bushings on front axle. I thought I had it ready for plow day when it would not start. Found that the diesel fuel went bad and turned into brown puddy. After...
  2. 4

    Justifying a step deck

    I bought an 87 Transcraft 48" DD for $3500 but put a beavertail on it($3K), tires and rims($1600), paint($1200), and patching and welding flooring. It was a lot lizard and is heavy but rusty. Some places I go I can"t get it in so I bought a 34" hyd tail GN. I haven"t used it but I can haul more...
  3. 4

    corn header size

    Calmer has good products and I have delt with Clarke Machine in SD. Clarke make large heads. They put a 16 X 30 on a 9750 but it would not unload as fast as it could combine.
  4. 4

    corn header size

    Calmer has good products and I have delt with Clarke Machine in SD. Clarke make large heads. They put a 16 X 30 on a 9750 but it would not unload as fast as it could combine.
  5. 4

    8970

    I had a 8960 with 20.8X38 tires. No power, so I put a 400+hp pump on it. Also had to change the air intake to get more air. Ran great but coundn"t ride it because of power hop. I traded it for a 9400 with 800/55/42 trelleborg tires and rear weights. It weighed 50K. It was a 4 wheel drive 6030...
  6. 4

    9400 4x4 hard to start

    I had one that you would have to push the primer to get it to start after it sat 1 day or a month. Worse yet was the torque and hp! My 1997 8400 with a chip was almost as good. It had a 24 speed, and if you did shift down at 1800 rpms, it would die on you. I replaced the check valve in the back...
  7. 4

    Tilt Trailer Sudgestion

    I have a 22", 7K car hauler with 18" tilt. Like ericlb says, 1 narrow unit is okay, like small tractors, etc. I just ordered a Load Max GN 34" with 10" hyd tail with duals. I will be pulling it with F250 6.7 SRW short bed crew cab. This way I can haul 2 tractors and put the Kubota RTV on the...
  8. 4

    4020 Fuel Shut Off

    Should turn CW. It has been some time since I have used it.
  9. 4

    Can I pull a 7 shank disk chisel?

    I pulled a 13 shank with 2 railroad ties on the back with a ST310 Steiger turning 342hp. I was in heavy black central IL dirt. I was throwing lots of dirt. Stopped to measure-going 4" deep. I then bought a DMI that would separate the men from the boys. But it all depends how deep you go - 4" or...
  10. 4

    No. 5 nearing completion!

    I have also mowed many acres with one,about the end of August when the ragweed pollen would be foging and the thorn neddles would flaten the tires in our timber pasture. This pasture is now part of the Clinton Lake in central IL. Part of it is under water and the rest is over grown. Don't miss...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top