(800) 853-2651
SHOP NOW

Recent content by 42toro

Yesterday's Tractor Forums
  1. 4

    Ford 120 8NNN part numbers

    Yes, I used a Testor's paint pen. Clear coated the entire hood afterward.
  2. 4

    Ford 120 8NNN part numbers

    Duner, That really clears up a lot. The Toro parts manual uses that same "ONY" prefix on many other non engine parts. This clarification really makes sense now. Thanks!
  3. 4

    Ford 120 8NNN part numbers

    Thanks for your input. When I lookup your timing cover it look like I am trying to locate one like this. With motor mounts
  4. 4

    1939 Toro Bullit aka Allen Tractor (See Photo)

    Bob, I just found your old post. I have a couple of these units. Also have a bunch of promotional material
  5. 4

    Ford 120 8NNN part number update

    I have receives several great responses. Thanks to All. What I am still looking for is the timing cover. I did receive an email with a photo of the exact cover and oil pan that I am looking for. Any ideas where to find them? Thanks
  6. 4

    Ford 120 8NNN part numbers

    Yes, it is set up for a governor. Just a plain plat cover with a line from the oil filter. It is all cast as one piece and not aluminium.
  7. 4

    Ford 120 8NNN part numbers

    The motor mount frame is actually connected to the timing gear cover. All one cast piece.
  8. 4

    Ford 120 8NNN part numbers

    Over the years I have acquired several of these Toro series II units. I am needing several parts to finish some of my projects. These have what I believe is a Ford 8NNN industrial motor(very similar to the 8n motor). All that I have torn down do have sleeves, no governor, and a timing cover that...
  9. 4

    ammeter activity

    1949 toro general with 1939 dump trailer
  10. 4

    ammeter activity

    Thanks for the input. I will ride with the lites on. Your info is very helpful. There are about 600 tractors on this ride. I will post photos next week. thanks again
  11. 4

    ammeter activity

    Just installed a new wire harness in my 1949 Toro general. It is powered with a 9n motor. I also replaced the -resistor -cut out -coil -6 volt generator -points -plugs -ammeter upon start up switch on and head lites on ammeter shows -12 amps. Adjusted the screw on the back of the genny and at...
  12. 4

    oilite rock shaft bushing for MF 14

    I am looking for oilite bushings for my Massey Feregson 14. This is the bushing that holds the rock shaft to the frame. I have been unsuccessful with the dealer. I would be interested in new or experenced.
  13. 4

    52 8N

    Keep it. Just don't line it up near the others. Maybe she won't catch on.
  14. 4

    At what point do I decide to do a total rebuild?

    A 1942 Toro Master B. Has set for the last 25+ years. Where do I start? This is a 9N motor. Industrial
  15. 4

    Blasting and painting

    I recently visited a shop in Milo. Looked like a decent setup. MID-IOWA RESTORATIONs. tractors is are main thing. we do everything from cleanup,blasting,wiring,gauges ect top end paint jobs. Bret Halls 515 205 4509 15580 s23 hwy milo,ia 50166
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top