-
4
is there 2 different rear ends for a 821?
so I have 2 821 Fords and they seem to have 2 different rear ends....from what I read they were a special utility and did not come with 3 point or PTOs...So I have 1 with a 3 point and pto....so someone at some point put a rearend that had a 3 point and PTO...and it has ears on the axle ends... -
4
what is # for oil filter for 172 ..4 cyl. gas ford 821
thank you for the different options... -
4
what is # for oil filter for 172 ..4 cyl. gas ford 821
I have a Ford 821 4 cylinder gas engine with spin on filter on side of motor...Looking for a filter number ? -
4
how to remove relief valve eaton pump
ok so upon calling a guy who has rebuilt many of them he says that the small port is just nothing in there ..has nothing to do with relief..the flow control and relief valve is all together in 1 assembly and can not be adjusted or taken apart...is all 1 unit..and its impossible to take it... -
4
how to remove relief valve eaton pump
Well the picture shows the flow control valve which is the bigger hole...and then the smaller port at botton is the pressure relief ..so my diagram shows a C-clip holding the valve in ..but i dont see one inside my pump? so maybe someone has taken it out..but either way I cant seem to figure... -
4
power steering pump 600 thru 5000..design issue?
Oh yes I forgot..the rollers are just not put back in...I was just showing the rotor compared to the odd shaped hole? it was not round so I thought something was wrong...but its just the design then? .and how do i get the relief parts out? -
4
power steering pump 600 thru 5000..design issue?
ok so the rotor is correct, and the flow controller goes in with the tube with the ball down and in first like in my previous picture.....so yesterday I called around and got with a guy at a New Holland dealership..he found an old servive manual..here is what he sent me..? am I missing some... -
4
power steering pump 600 thru 5000..design issue?
..ok I have some questions...email me [email protected] where do you live ? -
4
power steering pump 600 thru 5000..design issue?
well I found out from the dealer that the power steering flow control/pressure relief assembly does not come apart. i now which direction it goes in and what typr os spring it calls for as mine was all broke up im many piedes..there do not sell that part and it has to be source lovaly ....but... -
4
relief valve Ford 821 is this correct ?
Thanks John as I do have a better picture someone sent me ..but I still cant tell what or how that is made ..hopefully soneone will temm me howto take it apart... figure 13 an O ring I dont understand and also figure 12 I can see the ball, and the rest is ??? I hope to get someone who... -
4
pwr steering relief valve / how to dissamble?
does or has anyone ever dissasembled this power steering pump Flow control /pressure relief valve before.. I see the ball is frozen and wont move and so Has anyone ever got one apart without damaging it ? and is there a spring inside it too?..its a Eaton pump... I donrt want to try to take... -
4
Ford 821 low pwr steering pressure
thanks for the diagram...but i still cant figure out from the drawings which way the plunger goes....the drawings are not clear..for the plunger... -
4
Ford 821 low pwr steering pressure
email me at [email protected] Im in Toledo Ohio -
4
Ford 821 low pwr steering pressure
so where you located ? Im interested...mark -
4
relief valve Ford 821 is this correct ?
So the problem I think is when I took this pump apart there was a broken spring .. shown in picture is what was left of it.. and the plunger has a ball bearing in the end of the tube and its stuck closed..I tried to pust ball bearing in but not going .... ..So first of all do I have the parts...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy