(800) 853-2651
SHOP NOW

Recent content by 460puller

Yesterday's Tractor Forums
  1. 4

    Farmall M repower

    Typically people use the stock SBC flywheel and redrill the bolt pattern to use the M pressure plate and clutch disk. You might have to machine the input shaft to the desired length and pilot bearing o.d. or make an adapter for the original pilot bearing. Using the stock SBC flywheel...
  2. 4

    460 puller

    If you decided not to remove all of your gears that drive the main pump and want to keep power steering some people just remove the main pump section gears so it doesn't, pump and keep the small steering section. You should be able to look at the small line porting when taking the flow control...
  3. 4

    460 pto removal for puller

    We removed every gear and shaft from the IPTO shaft at the pressure plate out the back. The front half of the TA is dry and with no oil slinging around by removing the gears we don't need an input shaft seal. There is a seal for the TA right behind the dry clutch. The parts you are talking about...
  4. 4

    460 pto removal for puller

    We have run for 4 years with everything removed with no issues and have inspected since. The planetarys get lubed from a trough in the speed transmission that runs to the TA gear section and fills to a level then drains back to the transmission.
  5. 4

    Sleeves

    SE wisconsin does great work
  6. 4

    Sleeves

    No need to braze call Mike at HH and he can set you up 608-332-3797
  7. 4

    red diamond 450

    4.625 easy
  8. 4

    div 5

    I was watching Div. 5 at Tunica on you tube and there were Farmalls with RD engines , I thought RD engines were not allowed in Div. 5 so are they allowed or not , or sometimes ? I am confused
  9. 4

    Stroke on a RD 501

    5.25 stock most are going 6.00
  10. 4

    Sigourney

    Is that 3000 RPM and stock block ? or can a Red Diamond run ?
  11. 4

    Sigourney

    I heard there may be a 12 MPH class at Sigourney this spring , does anyone know the rules ?
  12. 4

    M gear

    Thank you
  13. 4

    M gear

    What is the diameter of a Farmall M cam gear ?
  14. 4

    Best updraft carb?

    I agree the 7700 combine carburetor works great but are hard to find and are expensive , but a reworked stock carb with larger throat and v venturi would also be an alternative.
  15. 4

    Rd 406 Farmall 560

    Message me if you like but you will need a new flywheel for sure and a new backing plate to mount it to the bell housing, you will also need to fabricate new front engine mounts and naturally make room for new exhaust depending on what manifolds you decide to use. The engine is about 6 inches...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top