Recent content by 48oliver70

  1. S

    Farmall 656 3pt problem

    I have an early model 656 gas tractor, manual trans. The problem is that I can't get the hitch to raise with the position controller but when I pull the load control back to light or towards the rear of the tractor it will raise regardless of position control lever. When I push load control back...
  2. glennster

    beans DID look good

    got 3.4 inches of rain last nite. this is my quarter section field. looks like close to a third is underwater. getting pretty late for a replant, supposed to get more rain this week. lot of roads flooded, creeks way out of banks, got a lot of corn in the water, hoping that will make it.
  3. T

    Fuel and rubber

    Bought a mower in 2005 with a BS engine.....don't know if that has anything to do with it or not as most engines have to do what I am about to say somehow. Recently it has been running rough and I've been chasing a ghost. I've been looking in the wrong places. In short there was nothing wrong...
  4. 4

    51 g pedestal

    I have a 51 g and I am looking to lighten up for pulling. I have a split pedestal on the front with the rollomatic. What other pedestal will fit? Thanks Mitch
  5. 4

    John deere G carb problems

    try this again https://youtu.be/Jg6s7EeGdoY
  6. 4

    John deere G carb problems

    Heres the video
  7. 4

    John deere G carb problems

    Just recently picked up a john deere G with the DTLX 51 carb. Problem I'm having is it idling. Took carb apart let soak in the parts washer for a better part of the day. Blew out every hole I could find. Put the carb back on and it runs better. Runs great at high idle doesn't skip a beat. Low...
  8. 4

    Oliver 70

    What did you put in for pistons? And how big is the stroke?
  9. 4

    Oliver 70

    Okay I'm building an oliver 70 to pull 3500lbs-5500lbs. I know not the best tractor to work with but what can I do besides shave the head.
  10. 4

    Oliver 70

    Okay I'm building an oliver 70 to pull 3500lbs-5500lbs. I know not the best tractor to work with. But what can I do besides shave the head.
  11. 4

    70 Orchard

    Is it an orchard or standard? How much are they asking for it? Does it run? If it's an orchard has all the fenders and side curtains and in really nice condition then I would go for it depending on the price. -Mitch
  12. 4

    Oliver 66 Road Gear Speed

    Well, my 70 does about 20-25mph in 6th with 13.6x38 tires. Obviously that's not with stock engine speeds, but with stock motor. As said before it really matters on what your engine speed is and gearing.
  13. 4

    Oliver 70 Pulling

    Okay so the bore of an Oliver 77 is 84mm and the bore of a Oliver 70 is 79mm. talk to my machinist he said he will split that difference 2.5mm off the block and shave the sleeve down 2.5mm. Now my question is are the Oliver 70 wrist pins the same size as a 77 wrist pin? If not what does work?
  14. 4

    oliver 70 Pulling

    I have heard that you can put Oliver 77 sleeves in an Oliver 70 motor with some work. Has anyone done this before? If so how much work was it? Trying to get some extra HP for tractor pulling. Tractor pulls good (max 10,100 lb. in stone boat) but needs a little more power.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top