-
6
Oldhokie sleeve puller
Got one I don't use; got the set for the 600 and 800 motors. email open, if interested -
6
Harbor Freight welders
Look at eastwood; they have been running some great sales on their 120 V mig welders I think I picked one up shipped on sale for 200 (http://www.eastwood.com/mig-welder-110vac-135a-output.html), looks a little bit more but good one for the $. I have the 240 version as well (was 500) and it is... -
6
suspension seat on a Z-turn mower
I just bought a Gravely ZT-HD 60 and I bought and installed this: https://www.amazon.com/gp/product/B01M2XIB0R/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1 It does make a difference; had to drill some holes to get it to work, and add a spacer (nut) on the bottom but it worked out great...- 6t6cuda
- Post #1
- Forum: Tractor & Farm Talk
-
6
Buying a newer tractor on Craigslist
Thanks all, this is what I was looking for; still a crap shoot, but it looks like you can check with the state / county to see if it has a lean on it. Still going back and forth if I want to go forward with it at all, but just getting some background info...- 6t6cuda
- Post #1
- Forum: Tractor & Farm Talk
-
6
Buying a newer tractor on Craigslist
There is a newer tractor near me on Craigslist that I might be interested in. How do I ensure there is not a loan / lean on the tractor before buying it? there is no title transfers for tractors in my state. I don't want to end up forking over a lot of cash only to find out that the bank still...- 6t6cuda
- Thread
- Replies: 10
- Forum: Tractor & Farm Talk
-
6
Stuck intake push roads Ford 641
Hello, Well, the bent pushrods are because the intake valves are stuck... Two intake valves, the #1 and #4. The engine was rebuilt about 100 Hr ago and it gets light use, grader blade / cutting 5 ac with finish mower. I don't remember if I replaced the valve guides with the rebuild or not it... -
6
Bent pushrod '57 641
Thanks to all, got a set coming from ebay, and a set with rockers coming from ebay. Hopefully they will work in this application. Thanks for the heads up on the length differences; and other information! -
6
Bent pushrod '57 641
It is the #1 and #4 intake valves. It was a rough measurement based upon a caliper I could not get quite square - I figured it was good enough to see if they were 1/4 or 5/16. They are just a few thou over 1/4" -
6
Bent pushrod '57 641
Went to start the tractor this afternoon, and something sounded funny as soon as I started cranking... I don't know why, but I thought about the pushrods, and yep they were bent. two of them were... Anyway looking for replacements new/used and I see there is a 1/4" version and a 5/16"... -
6
2004 jeep grand cherokee transmission
On most Chrysler automatic tras, the pump will only be engaged in neutral, not in park (like GMs); so I would put it in N and let it run at idle for a while and see if it starts to build pressure. That is why the dip stick will say check with trans in N not park as it does on GM cars. I... -
6
Value of '62 FORD TLB
That is about what I thought (around 4k) ... It would be good for a one job and done (which is what I did). Might get it cleaned up and running in the spring and list it and see what happens... -
6
Value of '62 FORD TLB
Hello, I have a Ford TLB (821 / 703 Loader / 713 hoe) Power steering, 4 speed, I think I might want to get rid of. It runs drives, digs, but will need some TLC, Some cyls will need to be rebuilt in the future and some hoses will need to be replaced; the pins are very loose in the hoe (but... -
6
seeking history of 3 point hitch/PTO type/incompatibilities?
I know many on here are MUCH more experienced than me, but in short; there are 4 variants of the 3 point hitch. They are all basically the same (two movable lower arms at some length and spacing, a single upper link with an adjustable length). The size of the holes and locations of the...- 6t6cuda
- Post #1
- Forum: Tractor & Farm Talk
-
6
Best modification made to your tractor?
1 - 12V - no more expensive batteries to buy, plus can use "hand me down" car batteries that are not "reliable" enough for a car 2 - Cup holder (actually the previous owner added this one)- 6t6cuda
- Post #1
- Forum: Tractor & Farm Talk
-
6
solenoid for 12V conversion 641
I think that is what happened to me. It is the wrong part i.e. not an insulated coil as you have described. They said I could return it, pay shipping to get my $6 back... Guess I will order one from NAPA or someone...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy