(800) 853-2651
SHOP NOW

Recent content by 7030466

Yesterday's Tractor Forums
  1. jon f mn

    today's funny

    .
  2. L

    Hydraulic Control Valve

    This control valve was with a group of parts I bought at an auction. It was new in a John Deere box. The number on the outside of the box is either 63558 or G3558. The casting number is 31518-20. Does anyone know what the control is for? I assume it is for a loader
  3. L

    feature night?

    tonights feature night is sugested by Royce,,,he says ...show any homemade tools or let us know about some you have made
  4. C

    bathroom supplies use

    my sometimes g/f just got back from shopping for me. I caught immortal H*** for my paper consumption. How many sheets do you use per job?
  5. A

    rotted fuel return sleeves on injectors 3TN Yanmar Diesel

    The sleeves that have the fuel return lines are rotted and i was unsure if i should replace the entire injector with another used one or is it possible to just replace the rotted part without effecting the operation of the injector. Is there anything in particular i should know about these...
  6. 8

    8N split

    I am planning on splitting my 8N to replace the transmission seal, and while I am at it probably the clutch. My question is, approximately how many hours does this take start to finish? Thanks
  7. B

    Magnet paints

    Anyone familiar with Magnet paints? Good-bad-maybe?
  8. 7

    John deere cams

    How is it done or who can I talk to for more informantion.
  9. 7

    John deere cams

    Was at a pull and some were talking about moving the cam in john deeres for more stroke. Can it done are they just dreaming?
  10. 7

    WD_45 Crankshaft Oil Seals

    Drop oil pan remove last main cap and unbolt or rotate top seal holder out install new seal.
  11. 7

    5 year old stroker crankshaft

    The crank I want to see is the one deerelure is going to put the billet rods on.
  12. 7

    Custom connecting rods

    You will have to worry about your crankshaft before you have to worry about the rods. Can you post a picture of your crankshaft and let everyone comment on it.
  13. 7

    3020 Diesel

    How much oil does a 3020 diesel use for a oil change in the engine.
  14. 7

    rebuilds don't last in 429 ?

    What do you call a rebuild? More to a rebuild then a sleeve kit. Was head redone, crankshaft injecters, pump,block prep and cleaned with a hot tank and all parts cleaned,put together in clean area, not outside under a tree.
  15. 7

    39 JOHN DEERE B

    you can bore the block and use late b or 50/520 pistons
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top