Recent content by 78CJ

  1. 7

    Parts interchangeability

    Besides the housing (aluminum vs iron) how compatible are a 1948 TE20 and a 1950 TO20? I currently have a TE20 that runs and drives but needs a lot of work. I have an opportunity to buy a TO 20 that looks to be in pretty good condition. I am thinking of buying the TO and then I would have a...
  2. 7

    Another TO-20 Hydraulic Question: Sticks Up

    I am currently still battling the same problem. Could you explain how to adjust the spring? Thanks Ryan
  3. 7

    My 1948 TE20 Quit

    New condenser didn't do it. I don't have spark at the plugs but when I turn it over the points don't really open and just kind of sit there are spark intermittently. I can actually open the points by moving the rotor side to side by hand.
  4. 7

    My 1948 TE20 Quit

    Darn, just went back out to check and I left the key on. Battery is dead now. I bet I was turning it over yesterday when I had power on the distributor side of the coil. I did not have spark at the plugs when I tried yesterday by taking one out and grounding it.
  5. 7

    My 1948 TE20 Quit

    What do you mean by low tension wires? The one from the negative side of the coil to the dist? Because I did replace that.
  6. 7

    My 1948 TE20 Quit

    I fired up the TE20 to go work a food plot yesterday and as I was hooking up the harrows it died, no spit or sputter just like someone turned the key off. I have power on the hot side of the coil and yesterday had power on the negative side but today none. Will a coil just die? The last coil...
  7. 7

    TE 20 Hydraulic issue

    Hmm, this all seemed to start after I pulled the shaft to replace a leaky seal. I wonder if it got crud in the oil.
  8. 7

    TE 20 Hydraulic issue

    I bought the tractor from an estate in Jan 2015. I took it to a shop and had them change all the fluids and get it up and running for me. There was so much water in the trans that it had frozen solid and we had to drag it on the trailer. I picked it up from them in May 2015 and that was the...
  9. 7

    TE 20 Hydraulic issue

    I have freed it by doing this in the past, so should I get a new valve or just change the oil? Thanks Ryan
  10. 7

    TE 20 Hydraulic issue

    So if the control valve is sticking what could be the cause?
  11. 7

    TE 20 Hydraulic issue

    I have posted previously that the 3 pt on my TE 20 has started to not want to go back down after lifting up. I still have not had a chance to pull things apart but one thing I did notice is that the oil level is low. Will this cause the problem? I ask because I don't want to add oil to...
  12. 7

    3pt staying up on TE20

    That makes the most sense because it just started happening out of the blue. I assume I should plan on taking the entire pump out? When I was in there I did not see this part but was not specifically looking for it either. Ryan
  13. 7

    3pt staying up on TE20

    It seems like the valve is traveling too far out of the pump allowing it to get cocked in the bore and not slide back in. Does that make sense? Is there an adjustment?
  14. 7

    3pt staying up on TE20

    Was working a field day before yesterday and out of the blue when I raised the cultivators they just stayed up and would not go down. It was late so I just left it and returned yesterday after some research and searching. When I started it up the 3pt worked. So, I figured I would continue in...
  15. 7

    My TE20 ate its starter

    I took the starter to a local shop I know well. Had it fixed up in a day. He also converted it to 12 volt as he said that they have repaired many unconverted starters that have detonated from spinning double the speed when impacting the ring gear.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top