(800) 853-2651
SHOP NOW

Recent content by a1cnc

Yesterday's Tractor Forums
  1. A

    case 580g will only start with a whiff of ether

    A compression test will tell top end condition. I was sort of thinking the cold start device might be part of the problem as it doesn't seem to do anything
  2. A

    case 580g will only start with a whiff of ether

    I lapped the valves and did a vacuum test after. All the seats/ faces were not bad before I just figured I would do that while it was apart.
  3. A

    case 580g will only start with a whiff of ether

    I have this machine running and moving now. History is, Blown headgasket between 2-3 when I got it. Did a valve job. planed the head. Checked deck of block and it seemed ok. New gaskets. It runs ok once warmed up but it will not start without a tiny shot of ether. Temps are 70+ F. The cold...
  4. A

    Case 580G freshly rebuilt shuttle no fwd/ reverse

    Thought I would post back with the fix. Turned out the pickup screen was plugged. Once I cleaned that and re-filled it the shuttle is working great! When I took the shuttle apart the first time I found a rag wrapped around the output shaft INSIDE the shuttle. I am pretty sure there was still...
  5. A

    Case 580G freshly rebuilt shuttle no fwd/ reverse

    Sigh, Hooked up a gauge and MAYBE 5 psi. Draining the shuttle now. Oil looks fine, no signs of water , or metal. Probably going to pull the control valve one more time just for good measure and see what I see
  6. A

    Case 580G freshly rebuilt shuttle no fwd/ reverse

    Well this one got a full rebuild. Pump, Torque converter, discs. Hope I didn't screw it by not replacing the cooler
  7. A

    Case 530 doesn't stay running.

    Not as familiar with the gas models but a gas motor is a gas motor. I have heard of ignition coils failing when they get hot. Check for spark when it dies. Could be a weak fuel pump. Maybe a pressure gauge Could be a bad breather on the fuel cap. Open the fuel cap and run it and see if it...
  8. A

    Case 580G freshly rebuilt shuttle no fwd/ reverse

    hmm You're NOT being the bearer of good news here...;) But, thanks for the ideas. Guessing if the drive lugs sheared my pressure will be low/ non-existent
  9. A

    Case 580G freshly rebuilt shuttle no fwd/ reverse

    Thanks will do, At least the pressure relief is on the outside.
  10. A

    Case 580G freshly rebuilt shuttle no fwd/ reverse

    I did replace the converter with a rebuilt. I hopefully cleaned the cooler by flushing. New pump in the kit. I put new metal sealing rings on the shaft but the kit didn't come with the teflon rings. The declutch shuttle was stuck in the selector shaft but I freed it up and put it back...
  11. A

    Case 580G freshly rebuilt shuttle no fwd/ reverse

    Just rebuilt the shuttle on this machine, The history is, I bought it with the shuttle already out needing a rebuild. There were a couple broken springs inside and a rag inside wrapped around the output shaft and the inlet screen was plugged with fibers from the rag. The clutch plates showed no...
  12. A

    Case 310 and Case 350

    What is wrong with your injection pump? You can buy the seal kit inexpensively but If your'e not adventurous there is a guy on Heavy equipment forum that rebuilds them. I believe there is someone on this forum too that does it.
  13. A

    Case 530 Questions with Pictures

    Your 530ck is similar to mine. It has the low high range lever on the right. It has a case-omatic torque tube (Predecessor to the power shuttle) The left lever is forward/reverse (lever forward for reverse). I believe it has a wet clutch and a torque converter. The clutch pedal is depressed...
  14. A

    350 dozer update

    Mine has a roosamaster pump. Forget the pump # but if you need it, I can get that for you
  15. A

    Case 350 Dozer Gauges - Where to find?

    TRy these guys. https://www.elmersrepair.com/er-g45257
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top