(800) 853-2651
SHOP NOW

Recent content by agjim

Yesterday's Tractor Forums
  1. A

    Stupid question, (ford 9N)

    I agree with Jim, use a 12v starter from a late 50's or early 60's model ford car or truck. it's a 12v and the 12v starters had a shunt winding in them to slow them down. The 6v starter had 2 field windings, the 12v had 3 windings. I usually preferred a 6v starter for my applications so if I had...
  2. A

    Help identify this tractor

    Thanks for the information. I'm still interested in finding out what the number means that is stamped below the seral number. I have a gold demonstrator that does not have a sn or model number but has a number stamped on right side of the transmission housing. I think the transmission was...
  3. A

    Help identify this tractor

    I see the 641 stamped on the flat spot and it looks like the factory stamping BUT I have never seen a 641 with brake shaft going thru the bellhousing area of the transmission, I thought that was only on the 640. I'm also curious about the number stamped below the serial number. That number is...
  4. A

    Help identify this tractor

    I have this 641 sn 15286, number below sn is 106119, engine date code j117. The left brake shaft goes thru the bell housing area of the transmission and the clutch pedal pivots on the brake shaft (640 rather than 641). The underside of the hood has never been painted gray. Is it a 641 or a 640...
    • agjim
    • Thread
    • Replies: 6
    • Forum: Ford
  5. A

    6000 steering valve

    I'm looking for a 6000 steering valve that mounts in front and under the radiator. It had 3 bolts holding it on and 4 lines. Let me know if you have one you would consider selling. (PN C3NN3A730A)
    • agjim
    • Thread
    • Replies: 0
    • Forum: Ford
  6. A

    NAA engine plate thick or thin

    The NAA takes the thick plate.
  7. A

    NAA engine plate thick or thin

    A agjim
  8. A

    Massey Harris 50 High Altitude

    I have a picture of the SN plate if that helps identify my tractor. Thanks
  9. A

    Massey Harris 50 High Altitude

    The tractor is about 40 miles away from me now but I'll get the numbers and letters that's on the plate when I get back to it. Thanks. Jim
  10. A

    Massey Harris 50 High Altitude

    I have a MH 50 with factory LPG. There is a plate on the engine block stating this tractor should not be operated at altitudes below 5000 ft. What is the reason for this restriction and what else can you tell me about this tractor?
  11. A

    Dorset 363

    I did a little figuring on putting a B Cummins in a 6000. My best plan was to tilt the engine slightly to the right to have room to get the starter between the engine block and the side rale. I did not want to alter the side rail. The 4 B or 4 BT will have as much or more power than the...
  12. A

    Dorset 363

    The closest thing to "fitting" is the 223 and 262 car and truck engine. It will bolt in but you'll have to fabricate governors and hyd. pump drive. The car and truck engine will have a down draft carb. which will interfere with the fuel tank. I used a diesel manifold by welding a flange for...
  13. A

    three blade fan Ford 860

    Check the ignition timing. Retarded ignition timing will cause overheating.
  14. A

    sos transmission

    I have a '63 4000 SOS. I built the trans myself about 5 years ago but I have been working on them since the '70's. I did not have to put bands nor any hard parts in it. Still I spent about $1000 on gaskets, seals, and clutches and I did not charge myself labor. If you don't have special...
  15. A

    Pictures from the Weiss Lake Club & G Roundup Show this weekend

    Thanks for the pictures. I enjoyed the show and enjoyed talking with so many good friends. I missed seeing the ones who were unable to come. Jim
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top