(800) 853-2651
SHOP NOW

Recent content by allisue

Yesterday's Tractor Forums
  1. A

    8n genny wires

    Thanks, I think with the info you and other have given me I can figure this thing out without calling a friend. She is really running good now once I replaced crankshaft pulley and I think if I can get these genny wires on I'll be problem free for a while. Mark
  2. A

    8n genny wires

    Thanks, I'll check the regulator out. Mark
  3. A

    8n genny wires

    Thanks, I'll check the regulator and your right getting the charger out every time is a pain and really stupid. Mark
  4. A

    8n genny wires

    I have just bought a new genny for my front mount dist. 6v. 8n. (year model??) I took off the wires from the old genny and forgot to note which wires went where. ( Arm, Field, Ground.) The wiring is new and I have a black, red, and white wire setup. Can anyone help me as to which wire goes...
  5. A

    Dies when bushogging?

    Thanks, I replaced the coil just recently so I am hoping a carb adjustment is the key. We'll see. Mark
  6. A

    Dies when bushogging?

    Thanks, I messed with the carb this summer and I think I probably messed it up with the proper richness. I'll adjust and see what happens. Thanks, Mark
  7. A

    Dies when bushogging?

    Ok, I am a rookie at this so forgive me. Tell me where the points are and what you mean by gapped. Thanks, Mark
  8. A

    Dies when bushogging?

    Thanks, I'll check it. Mark
  9. A

    Dies when bushogging?

    Thanks, I did mess with the carb last summer and I have no idea what I was doing. Clocwise or counterclockwise on the adjustment. Thanks Mark
  10. A

    Dies when bushogging?

    My 50 8n 6v front mount dist. will start right up. No smoke. Running perfect and will start to die after about 15 minutes of bushogging. Grass is tall but dead right now. I am not cutting too low and I have just sharpened blades on the 4 foot cutter. Once it begins to die I can kill the bushog...
  11. A

    Which pulley do I need?

    Thanks a lot, no loader. This board is great. Mark (Arkansas) (Tornado country right now)
  12. A

    Which pulley do I need?

    I have gotten a lot of help on the board here. One more question. I am replacing my crankshaft pulley on my 50 8n 6v front mount dist. When I look the part up, there are 2 available. One has threaded holes an one has 4 rubber bushings. I have no idea what the difference is. Does anyone know...
  13. A

    front crank bolt and key

    Thanks for the help.
  14. A

    front crank bolt and key

    I have just got to my crankshaft pulley and there is no "key" or bolt there. The pulley was just spinning. My question is: What size bolt and key is this? I have a 50 8n front mount 6v. The pulley is cracked where the notch is. Next question: Can I get these at O"Reilly"s or NAPA or must I order...
  15. A

    Fan blade won't turn. Tried everything.

    Thanks, I hope it is just the pulley.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top