(800) 853-2651
SHOP NOW

Recent content by alrman

Yesterday's Tractor Forums
  1. A

    proper brake for 580c backhoe

    Any Case hoe up to & including a 580C used DOT3 brake fluid. Models from the 580D onward used mineral oil. In short - use DOT3 brake fluid. Cheers
  2. A

    Case 550 G torque converter pressure question

    There is a difference in the plugs for those valves. Had trouble once many years ago....they will effect the operation of the valves. If they are swapped around, the machine won't drive. I can't recall exactly the difference, a drilling in the plug perhaps. Might be worth another look.
  3. A

    Case 550 G torque converter pressure question

    Have you removed & inspected any of the valves in the torque convertor housing during the repairs/replacements?
  4. A

    Case 550G dozer won't move, update and questions

    There is a park brake valve located on top of the transmission - next to the batteries. 1) Check for voltage req to release brakes. If no voltage check neutral start switch - lever raised to allow control lever operation. If power is present - check coil / solenoid operation - If coil is...
  5. A

    Case 580 SL series 2 stuck in 4X4

    That's good news Bill - glad to help
  6. A

    Case 580 SL series 2 stuck in 4X4

    If you raise the loader frame (& use safety bar) & raise the bonnet, working on the RHS of machine, behind the rubber flap - you can gain access to filter & valves. If you want more access remove the floor plate that is under your feet while in operators seat ...... if an air cab ...
  7. A

    Case 580 SL series 2 stuck in 4X4

    The 4wd solonoid is located on the top of the transmission. There are 2 x valves, a double (Fwd & Rev) & a single - 4WD. It requires power to the solonoid to engage 2WD. Power arrives to that solonoid without the aid of relays, so check if it has power or not - as to whether the...
  8. A

    Case 580 SL series 2 stuck in 4X4

    Is it a powershift or shuttleshift?
  9. A

    Case 1550 Dozer???

    1550 has hydrostatic drive - no convertor. Probably has blown a hose, no oil = no drive. Hopefully no damage has occured to pumps that will mean big dollars to repair.
  10. A

    Help reinstalling power shuttle into case 350 crawler loader

    No adhesive is required - those gaskets are usually a rubber ring - is that what you have?
  11. A

    Help reinstalling power shuttle into case 350 crawler loader

    They usually require a little twist & turn to get the splines to line up. Make sure the drive tangs for the pump drive line up. I usually put one set at 12 & 6 oclock & the other at 3 & 9 oclock. You should put some copper washers under the heads of the bolts of the pump. Oil can come from...
  12. A

    case tool

    Just wrap some duct tape around the axle stub so that it just leads up to the area where the seal makes contact, lube the taped shaft with some petroleum jelly, carefully slide the brake housing on to the stub using long guide bolts to hold shims etc When the cover is bolted remove the tape, it...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top