(800) 853-2651
SHOP NOW

Recent content by amattf

Yesterday's Tractor Forums
  1. R

    300 sleeves

    So I purchased sleeves and pistons from the Tractor Parts ASAP and they came last week. I did not get around to working on the project and am now wondering about installing them. They do not really start so I used inside-outside calipers first and then moved to micrometers and bore gauge set to...
  2. M

    Ford 2000 Power Steering Pump Replace

    Purchased my 68 Ford 2000, 3 cylinder motor, with non working power steering. I had a steering box leak and with the help of some of you guys on here, I rebuilt it. After the rebuild, nothing, no leaks, but no power steering. I have pump # C7NN3N675C with the separate power steering fluid tank...
  3. R

    Ottumwa Harvest Days and plowing cancelled for this year

    The Harvest and plow days in Ottumwa, Iowa, are cancelled for this year! Roger
  4. K

    Farmall H Broken Stud Bolt Of Water Jacket Behind Carb.

    In replacing the leaking water jacket of my 1939 Farmall H my friend and I've found a stud bolt is broken behind the carburetor. I'm thinking of drilling it out. To do that I'll need to remove the manifold, carb. and attachment to the governor. Is this reasonably feasible, or should I just try...
  5. N

    12 volt resistor

    On my Foerd 240 industrial engine on a new holland baler it just quit running start back and die found the resistor smoking I guess it is going bad,it has a resistor right before the coil and this is factory but can I put a 12 volt coil on it with a built in resistor and do away with this...
  6. showcrop

    50% do it

    I recently had Physical Therapy for a hip that is giving me trouble. The thread on the GMC pick-up tailgate reminded me what the therapist told me about effectiveness of PT. I got a referral to the orthopedic doctor who found a problem in the joint and gave me a steroid shot which of course you...
  7. K

    Oliver 90/99 water pump

    Hey, I need the parts to rebuild a water pump on an unstyled Oliver 99 4-cylinder tractor. I know there has been some topics on this before, didn't know if anyone had part numbers or places to get the parts to rebuild this water pump. Thanks.
  8. D

    End of summer project is over....

    I try to tackle something major every year late in the summer when things are slow. This year I decided it was time to start rebuilding the old dairy barn up by the road. It succumbed to an electrical fire many years ago. Close to 30 Holsteins were still inside. One of the surviving sons of...
  9. A

    1020 hydraulics haunted

    Conclusion: Finally got around to finishing this pump up. Ended up replacing the stroke control valve and seat like you suggested. Also replaced the piston springs and the outlet valve discs. These were cheap and I'll be replacing them anytime I open one of these pumps up from now on...
  10. A

    1020 pump rebuild

    Picture: https://photos.yesterdaystractors.com/gallery/uptest/a30325.jpg
  11. A

    1020 pump rebuild

    I'm rebuilding a pump from a 1020 that had weak to no hydraulics (see haunted hydraulics thread from last week). The symptoms were good standby pressure (2250psi) with no demand, 0 psi with any sudden oil demand. The crankcase inlet pin was very likely stuck (considering how hard it was to...
  12. A

    1020 hydraulics haunted

    So I bit the bullet and swapped pumps w/ my other "66 1020. 1 Power steering perfect 2 Rockshaft massively leaking by (lever won"t go down) 3 left remote working great, can tilt bucket just fine 4 right remote very weak (probably do to #2 above), can just barely lift loader So, I"ve still got...
  13. A

    1020 hydraulics haunted

    Oh, and I meant crankcase _outlet_ valve.
  14. A

    1020 hydraulics haunted

    Ok, I disconnected the remotes and rockshaft right before the priority valve and replaced it with a gauge. System builds to 2300, drops to 0 if I demand oil (turn the steering wheel). Also, when there is no demand for oil, it seems to "hunt" for standby pressure, sometimes won't build up until...
  15. A

    1020 hydraulics haunted

    Just capped the power steering; no change. What could I have missed on the rebuild? Replaced all o-rings, new thrust washers and quad ring, checked all the valves, etc. One inlet valve had a broken guide and was unscrewed, replaced that as well.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top